The independent technical support site for all things networking!


Post a new topicPost a reply Page 1 of 1   [ 12 posts ]
  Previous topic | Next topic 
Author Message
Vibovit
 Post subject: DSL-502T
PostPosted: Tue Feb 02, 2010 9:14 pm 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
I used RUC but it says that my DSL 502T is incompatible with RT firmware, my current firmware revision is the newest version. Is it possible to ugrade my router to RT 2.92? Here is the log file from RUC:

Code:
Router Upgrade Check 1.3.7 02-02-2010 21:14:42
Router IP: 192.168.1.1
CLI is needed
Description: D-Link 502T A5 revision
Board type: AR7VW
Product ID: AR7DB
Bootloader: adam2
RAM 16,0 MB
Flash (ROM) 4,0 MB
ADAM2: Yes
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build:
Firmware version: V2.00B12.AU_20070425
Firmware stamp: 20070425174401
CPU: MIPS 4KEc V4.8
DSP: 3.02.06.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: No
TIAP: No
TNETW: No
Wireless: No
WIFI chip: N/A
WIFI chip conf: No
Ports: 1
Marvell (or Marvell like): No
NSP: V2.00B12.AU_20070425
Manufacturers:
RNDIS: Telogy Networks Inc
HRNDIS: Telogy Networks Inc

Your current firmware is too old to upgrade to a RouterTech firmware.
Please upgrade to your router manufacturer's latest firmware and run this program again.


Can someone give me some steps how to upgrade my router to RT 2.92?
Top
 Profile  
 
mstombs
 Post subject: Re: DSL-502T
PostPosted: Tue Feb 02, 2010 9:50 pm 
Support Team Member
Support Team Member

Joined: Wed Jan 10, 2007 11:54 pm
Posts: 3169
Your firmware is not that old - 2007?
Code:
Firmware stamp: 20070425174401


but DSL driver, if this is correct is ancient ~2003

Code:
DSP: 3.02.06.00


and D-Link have stored a version number in the nsp box

Code:
NSP: V2.00B12.AU_20070425


Please post the contents of the env that the RUC will have stored, you should mask personal identifying MAC addresses.

Also see if you can connect with the RRT or PC-Tool, you will likely need one or the other to upgrade firmware.
Top
 Profile  
 
Vibovit
 Post subject: Re: DSL-502T
PostPosted: Tue Feb 02, 2010 11:24 pm 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
This is the env content, I upgraded my firmware from 1.0 to 2.0 EU version (via tiupgrade.exe) and then to AU version revision 12 (via web interface). Is it possible that my DSL driver didn't get upgraded?

Code:
setenv memsize 0x01000000
setenv flashsize 0x00400000
setenv modetty0 38400,n,8,1,hw
setenv modetty1 38400,n,8,1,hw
setenv bootserport tty0
setenv cpufrequency 150000000
setenv sysfrequency 125000000
setenv bootloaderVersion 0.22.02
setenv ProductID AR7DB
setenv HWRevision Unknown
setenv SerialNumber none
setenv my_ipaddress 192.168.1.199
setenv maca xxxx
setenv prompt Adam2_AR7DB
setenv firstfreeaddress 0x9401d328
setenv req_fullrate_freq 125000000
setenv mtd0 0x90091000,0x903f0000
setenv mtd1 0x90010090,0x90091000
setenv mtd2 0x90000000,0x90010000
setenv mtd3 0x903f0000,0x90400000
setenv autoload 1
setenv usb_vid 0x2001
setenv usb_pid 0x5b00
setenv usb_man D-Link
setenv usb_prod DSL-502T
setenv usb_board_mac xxxx
setenv usb_rndis_mac xxxx
setenv usb_serial xxxx
setenv autoload_timeout 5
setenv mtd4 0x90010000,0x903f0000
setenv StaticBuffer 120
setenv vcc_encaps0 0.0
setenv vcc_encaps1 0.0
setenv vcc_encaps2 0.0
setenv vcc_encaps3 0.0
setenv vcc_encaps4 0.0
setenv vcc_encaps5 0.0
setenv vcc_encaps6 0.0
setenv vcc_encaps7 0.0
setenv HWA_RNDIS 00:E0:A6:66:41:EB
setenv HWA_HRNDIS 00:E0:A6:66:41:E1
setenv modulation GDMT
Top
 Profile  
 
mstombs
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 12:04 am 
Support Team Member
Support Team Member

Joined: Wed Jan 10, 2007 11:54 pm
Posts: 3169
DSP drivers are built into firmware, no chance they are older, its possible it is really V6.2.3, but reporting of version number is wrong. Your mtd vars look fine for single image upgrade via web, suggesting firmware is not too old. The old adam2 version is fussy, but you have found tiupgrade works.
Top
 Profile  
 
Vibovit
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 1:08 am 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
Will modified tiupgrade below do the job of upgrading to RT?

Code:
DSL-500T Routertech 2.91.1 DSP 7.05 Flash Amd & Atmel (22.09.2009) -> Download (ftp://ftp%40adsl4all.net:adsl4all.net@adsl4all.net/Modem/Dlink/Dlink_DSL-500T/DSL-500T_Routertech_2.91.1_20090922.zip)
Top
 Profile  
 
thechief
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 9:00 am 
Development Team Leader
Development Team Leader
User avatar

Joined: Wed Feb 01, 2006 10:22 pm
Posts: 9328
Location: England, the Centre of Africa
Vibovit wrote:
Will modified tiupgrade below do the job of upgrading to RT?
You don' really expect us to answer that question, do you? I think you'd better ask whoever released that mod.

_________________
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.

Top
 Profile  
 
Vibovit
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 3:45 pm 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
I read that PPoE connections do not work under RT, is that true since my ISP uses PPoE?
Top
 Profile  
 
thechief
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 5:29 pm 
Development Team Leader
Development Team Leader
User avatar

Joined: Wed Feb 01, 2006 10:22 pm
Posts: 9328
Location: England, the Centre of Africa
Vibovit wrote:
I read that PPoE connections do not work under RT, is that true since my ISP uses PPoE?
There have been problems with specific ISPs in the past.

A good rule of thumb: if in doubt, then don't try it.

_________________
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.

Top
 Profile  
 
Vibovit
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 5:49 pm 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
Do you know if there is any way to enforce ADSL2+ modulation on my router using telnet? I mainly wanted to try ADSL2+ modulation but the firmware on my router doesn't have that option in web interface, and that's why I wanted to try RT.
Top
 Profile  
 
thechief
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 5:53 pm 
Development Team Leader
Development Team Leader
User avatar

Joined: Wed Feb 01, 2006 10:22 pm
Posts: 9328
Location: England, the Centre of Africa
Vibovit wrote:
Do you know if there is any way to enforce ADSL2+ modulation on my router using telnet?
Not with DSP 3.x

_________________
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.

Top
 Profile  
 
Pondera
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 7:16 pm 
Experienced
Experienced
User avatar

Joined: Sun Mar 25, 2007 4:06 pm
Posts: 217
Location: Brindisi (Italy)
@Vibovit
Maybe you can find a newer DSP than 3.x with this last release:

DSL-502T Ax NZ_3.00B02 - 20060710

If you want to upgrade via browser configuration download the package above and unpack it with WinRAR!

DSL-502T is exatly the same of DSL-504T without switch and plus a USB port: so I think that RouterTech can works on your device! :)

_________________
D-Link Unofficial Italian Forum | D-Link sites | D-Link AR7 ADAM2/PSPBoot

Top
 Profile  
 
Vibovit
 Post subject: Re: DSL-502T
PostPosted: Wed Feb 03, 2010 9:52 pm 
Novice
Novice

Joined: Tue Feb 02, 2010 8:16 pm
Posts: 25
Pondera wrote:
@Vibovit
Maybe you can find a newer DSP than 3.x with this last release:

DSL-502T Ax NZ_3.00B02 - 20060710

If you want to upgrade via browser configuration download the package above and unpack it with WinRAR!

DSL-502T is exatly the same of DSL-504T without switch and plus a USB port: so I think that RouterTech can works on your device! :)


I tried to use tiupgrade.exe from the rar but it gave me an error and my router's lights wouldnt power on reboot, the router was bricked (corrupted image mode didn't work). So I tried to de-brick my router with the firmware you provided and I had read FAQ before. I tried RouterRepairTool and it would stuck at 33% when trying to upgrade firmware (erasing mtd4), but luckily pctool 2.1 did the job and I managed to unbrick my router since Adam2 was there. The firmware you pasted has DSL firmware which supports ADSL2+, it's 5.0 version and it works fine, thanks again for providing the link :) My attenuation dropped and margin is much better on adsl2+ now :)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post a new topicPost a reply Page 1 of 1   [ 12 posts ]


Who is online

Users browsing this forum: Google [Bot] and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB & WordPress     Hosted by Kieran O'Shea     Site Code © 2009 Kieran O'Shea     All site contents © 2009 RouterTech - All rights reserved     Valid HTML     Valid CSS     Graphics by Neo