DSL-320T PPPoE not working

exploit · Post by **exploit** » Sun Aug 12, 2007 8:38 am

Hello everyone,

I have problems with PPOE connection, DSL Status is connected, DSL modulation type is ADSL.GDMT, VPI:8, VCI:35, and my username, password is correct, but on Connection status, State: Not connected

.

Current firmware is: RouterTech v2.3

Exept Routertech firmware I tried:

Code: Select all

DSL-320T Mcmcc 1.1.00.ZA 21.03.2007 DSP 7.0 (rev. 29.06.2007) 
DSL-320T McMcc 1.1.00.ZA 24.04.2007 DSP 7.0 (rev. 27.07.2007)
DSL-320T McMcc  1.1.00.ZA 24.04.2007 DSP 7.0 (rev. 29.07.2007) fix x flash Samsung 

DSL-320T RoterTech 2.20 Lite DSP 6.2 (rev. 08.07.2007) 
DSL-320T RoterTech 2.20 Lite DSP 7.2 (rev. 08.07.2007) 

DSL-320T RoterTech 2.30 Lite DSP 6.2 (rev. 08.07.2007) 
DSL-320T RoterTech 2.30 Lite DSP 7.2 (rev. 08.07.2007) 

DSL320_-_Acorp_1.0.17.RU.26122006_AnnexA_-_Jack_Mod_-_Signed

And on all of them I got this System log:

Code: Select all

Sep 16 12:00:08 | Valid Configuration Tree
Sep 16 12:00:08 | NTP Polling Timer for DHCP Started succesfully.
Sep 16 12:00:08 | DSL Polling Timer Started succesfully.
Sep 16 12:00:08 | PSP Boot environment  Modem Modulation Change: 0x3
Sep 16 12:00:09 | Firewall NAT service started
Sep 16 12:00:09 | Bridge Created: br0
Sep 16 12:00:10 | Bridge Created: br1
Sep 16 12:00:12 | Bridge Interface Added: eth0
Sep 16 12:00:18 | DSL Carrier is down
Sep 16 12:00:28 | DSL Carrier is up
Sep 16 12:00:29 | sar read trained mode (1)(ADSL_G.dmt)
Sep 16 12:00:30 | ---}}} Start of connection delayed for 27 sec
Sep 16 12:00:57 | PPPoE Launch after conn delay timeout ...
Sep 16 12:00:58 | pppd 2.4.1 started by root, uid 0

And PPOA is not working on my ISP..

Original firmware from DLink 3.10 is working and also I have DLink DSL-300T with firmware from JackTheVendicator (1.5 highreliability) and PPOE is working.

I tried so many firmwares, reset to factory values everytime, and even I uploaded a real "empty" MTD3, how bovirus1963 explained to me on noxirc, but nothing again

TNX

Post by **mstombs** » Sun Aug 12, 2007 9:41 am

You can tell from the log dates - that log is not from current official RT2.3!

Are you sure 8,35 is correct for your ISP? Also make sure LLC/VC-MUX and authorization CHAP/PAP is correct, and start with modulation mmode.

exploit · Post by **exploit** » Sun Aug 12, 2007 10:31 am

Hello again, and tnx for fast reply. 8,35 is correct for my ISP, and PPOA is not working on my ISP so I can't set LLC and VC--MUX (only PPOA?). I tried with modulation multimode but nothing again.

And yes its official RT2.3 firmware now....

Here is ROUTERTECH SYSTEM DIAGNOSTICS:

Code: Select all

ROUTERTECH SYSTEM DIAGNOSTICS

Operating system version
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) () #1 Mon Jun 4 16:50:45 BST 2007

Firmware version information
BUILD=RouterTech_3.6.0D_20070604_2.30
VERSION=3.6.0D-RouterTech-1P-PSBL
BOARD=AR7RD
FSSTAMP=20070604165328

PSP version information

Linux OS DSL-PSPOhioL version 4.5.0.5 Best and Final on BasePSP Version 5.7.6.12  Jun  4 2007 16:51:53 
Avalanche SOC Version: 0x10002b operating in cached, write back, write allocate mode
Cpu Frequency:211 MHZ
System Bus frequency: 105 MHZ


Driver version information
Texas Instruments CPMAC driver version: 1.5
Texas Instruments CPMAC HAL version: CPMAC 01.07.08 Jun  4 2007 16:50:57
ATM Driver version:[6.01.03.00]
DSL HAL version: [6.01.02.00]
DSP Datapump version: [6.02.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]

TI Linux LED Driver Version 0.1

Modem Modulation Information
NO_MODE				0x0
ADSL_G.dmt			0x3
ADSL_G.lite			  0x4
ADSL_G.dmt.bis			0x8
ADSL_G.dmt.bis_DELT		0x9
ADSL_2plus			0x10
ADSL_2plus_DELT			0x11
ADSL_re-adsl			0x20
ADSL_re-adsl_DELT		0x21
ADSL_ANSI_T1.413		0x2
MULTI_MODE			0x1
ADSL_G.dmt.bis_AnxI		0x0
ADSL_G.dmt.bis_AnxJ		0x0
ADSL_G.dmt.bis_AnxM		0x400
ADSL_2plus_AnxI			0x0
ADSL_2plus_AnxJ			0x0
ADSL_2plus_AnxM			0x2000
G.shdsl				0x0
IDSL				0x0
HDSL				0x0
SDSL				0x0
VDSL				0x0

System environment (/proc/ticfg/env)
BUILD_OPS		0x301
bootloaderVersion	1.3.7.15
ProductID		AR7RD
MAC_PORT		0
MEMSZ			0x00800000
FLASHSZ			0x00200000
CPUFREQ			211968000
MIPSFREQ		211968000
SYSFREQ			105984000
PROMPT			(psbl)
HWA_RNDIS		00:E0:A6:66:41:EB
HWA_HRNDIS		00:E0:A6:66:41:E1
HWA_3			01:e0:03:04:05:03
BOOTCFG			m:f:"mtd1"
cpmac_phy		0
mtd2			0x90000000,0x90010000
mtd3			0x90010000,0x90020000
mtd4			0x90020000,0x90200000
vcc_encaps0		0.0
vcc_encaps1		0.0
vcc_encaps2		0.0
vcc_encaps3		0.0
vcc_encaps4		0.0
vcc_encaps5		0.0
vcc_encaps6		0.0
vcc_encaps7		0.0
MODETTY0		38400,n,8,1,hw
MODETTY1		38400,n,8,1,hw
usb_vid			0x0
usb_pid			0x0
usb_man			N/A
usb_prod		N/A
HWA_0			00:19:5B:7D:3A:46
SerialNumber		00:19:5B:7D:3A:46
IPA			192.168.1.1
HWRevision		A1
eoc_vendor_id		0x444C696E6B000000
eoc_vendor_serialnum	00:19:5B:7D:3A:46_00000000000000
eoc_vendor_revision	20070523
invntry_vernum		2007052300000000
mtd1			0x90020090,0x90096000
mtd0			0x90096000,0x90200000
modulation		0x1

CPU information
processor		: 0
cpu model		: MIPS 4KEc V4.8
BogoMIPS		: 211.35
wait instruction	: no
microsecond timers	: yes
extra interrupt vector	: yes
hardware watchpoint	: yes
VCED exceptions		: not available
VCEI exceptions		: not available

Memory information
        total:    used:    free:  shared: buffers:  cached:
Mem:   6438912  6311936   126976        0    53248  1437696
Swap:        0        0        0
MemTotal:         6288 kB
MemFree:           124 kB
MemShared:           0 kB
Buffers:            52 kB
Cached:           1404 kB
SwapCached:          0 kB
Active:           1508 kB
Inactive:         1580 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:         6288 kB
LowFree:           124 kB
SwapTotal:           0 kB
SwapFree:            0 kB

Mount points
/dev/mtdblock/0 / squashfs ro 0 0
none /dev devfs rw 0 0
proc /proc proc rw 0 0
ramfs /var ramfs rw 0 0

Filesystems
nodev	rootfs
nodev	bdev
nodev	proc
nodev	sockfs
nodev	tmpfs
nodev	shm
nodev	pipefs
nodev	ramfs
nodev	devfs
	squashfs

MTD
dev:    size   erasesize  name
mtd0: 0016a000 00010000 "mtd0"
mtd1: 00075f70 00010000 "mtd1"
mtd2: 00010000 00008000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 001e0000 00010000 "mtd4"

Kernel modules
avalanche_usb          63296   0 (unused)
tiatm                 133520   1

Interrupts
  7:    46425   R4000 timer/counter [MIPS interrupt]
  8:        0   unified secondary [hw0 (Avalanche Primary)]
 15:      159   serial [hw0 (Avalanche Primary)]
 23:       80 + SAR  [hw0 (Avalanche Primary)]
 27:     1095 + Cpmac Driver [hw0 (Avalanche Primary)]
 31:       50 + DSL  [hw0 (Avalanche Primary)]
 32:        1 + USB [hw0 (Avalanche Primary)]

Devices
Character devices:
  1 mem
  2 pty/m%d
  3 pty/s%d
  4 tts/%d
  5 cua/%d
 10 misc
108 ppp
128 ptm
136 pts/%d
162 raw

Block devices:
 31 mtdblock

Processes
  PID  Uid     VmSize Stat Command
    1 root       1328 S    init 
    2 root            S    [keventd]
    3 root            S    [ksoftirqd_CPU0]
    4 root            S    [kswapd]
    5 root            S    [bdflush]
    6 root            S    [kupdated]
    7 root            S    [mtdblockd]
   92 root       2120 S    /usr/bin/cm_pc 
   94 root       1188 S    /usr/sbin/thttpd -d /usr/www -u root -p 80 -c /cgi-b
   97 root       3456 S    /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml 
  142 root        636 S    /sbin/dproxy -c /etc/resolv.conf -d 
  202 root        768 S    crond -b 
  261 root       1328 S    init 
  262 root        684 S    /usr/sbin/udhcpd /var/tmp/udhcpd.conf 
  263 root       2348 S    /usr/sbin/pppd plugin pppoe nas0 user glkis passw
  305 root       1332 S    /bin/sh diagnostics.cgi 
  306 root       1188 S    /usr/sbin/thttpd -d /usr/www -u root -p 80 -c /cgi-b
  319 root        612 S    /usr/local/bin/diagnostics 
  320 root       1332 S    sh -c /usr/local/bin/diagnostics.sh 
  321 root       1340 S    /bin/sh /usr/local/bin/diagnostics.sh 
  371 root       1328 R    /bin/ps aux 

ADSL Modem information

AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
	US Connection Rate:	188	DS Connection Rate:	1021
	DS Line Attenuation:	11	DS Margin:		31
	US Line Attenuation:	0	US Margin:		37
	US Payload :		7008	DS Payload:		0
	US Superframe Cnt :	24621	DS Superframe Cnt:	24621
	US Transmit Power :	0	DS Transmit Power:	9
	LOS errors:		0	SEF errors:		0
	Errored Seconds:	0	Severely Err Secs:	0
	Frame mode:		0	Max Frame mode:		0
	Trained Path:		1	US Peak Cell Rate:	443
	Trained Mode:		16	Selected Mode:		1
	ATUC Vendor Code:	4753504E	ATUC Revision:	2
	Hybrid Selected:	1	Trellis:		1
	Showtime Count:		1	DS Max Attainable Bit Rate: 19332 kbps
	BitSwap:		1	US Max Attainable Bit Rate: 76576000 bps
	Annex: 			AnxA	psd_mask_qualifier: 0x0000
	ATUC ghsVid:  ff b5 47 53 50 4e 00 0d
	T1413Vid: 00 00		T1413Rev: 00		VendorRev: 00
	ATUR ghsVid:  b5 00 54 53 54 43 00 00
	T1413Vid: 00 00	T1413Rev: 00	VendorRev: 00

	[Upstream (TX) Interleave path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Downstream (RX) Interleave path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Upstream (TX) Fast path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Downstream (RX) Fast path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

[ATM Stats]
	[Upstream/TX]
	Good Cell Cnt:	146
	Idle Cell Cnt:	186318


	[Downstream/RX)]
	Good Cell Cnt:	0
	Idle Cell Cnt:	1008672
	Bad Hec Cell Cnt:	0
	Overflow Dropped Cell Cnt:	0

[SAR AAL5 Stats]
	Tx PDU's:	66
	Rx PDU's:	0
	Tx Total Bytes:	2772
	Rx Total Bytes:	0
	Tx Total Error Counts:	0
	Rx Total Error Counts:	0


[OAM Stats]
	Near End F5 Loop Back Count:	0
	Near End F4 Loop Back Count:	0
	Far End F5 Loop Back Count:	0
	Far End F4 Loop Back Count:	0
	SAR OAM Ping Response Drop Count=15

Network statistics
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State      
tcp        0      0 *:www                   *:*                     LISTEN      
tcp        0      0 *:ftp                   *:*                     LISTEN      
tcp        0      0 *:ssh                   *:*                     LISTEN      
tcp        0      0 *:telnet                *:*                     LISTEN      
tcp        0      0 192.168.1.1:www         192.168.1.2:2139        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2137        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2143        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2141        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2131        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2130        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2135        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2133        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2123        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2121        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2127        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2125        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2115        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2113        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2119        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2117        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2171        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2169        TIME_WAIT   
tcp        0    332 192.168.1.1:www         192.168.1.2:2173        ESTABLISHED 
tcp        0      0 192.168.1.1:www         192.168.1.2:2163        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2161        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2167        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2165        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2155        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2153        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2159        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2157        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2147        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2145        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2151        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2150        TIME_WAIT   
tcp        0      0 192.168.1.1:www         192.168.1.2:2111        TIME_WAIT   
udp        0      0 *:domain                *:*                                 
udp        0      0 *:bootps                *:*                                 
udp        0      0 *:tftp                  *:*                                 
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags       Type       State         I-Node Path
unix  5      [ ]         DGRAM                    163    /dev/log
unix  2      [ ]         DGRAM                    165    /dev/klog
unix  2      [ ]         DGRAM                    130    /var/tmp/cm_pc.ctl
unix  2      [ ]         DGRAM                    144    /var/tmp/cm_logic.ctl
unix  2      [ ]         DGRAM                    503    
unix  2      [ ]         DGRAM                    407    
unix  2      [ ]         DGRAM                    270    
unix  2      [ ]         STREAM                   117    
unix  2      [ ]         DGRAM                    116

And system log:

Code: Select all

Jun  4 16:53:07 | Valid Configuration Tree
Jun  4 16:53:07 | NTP Polling Timer for DHCP Started succesfully.
Jun  4 16:53:07 | DSL Polling Timer Started succesfully.
Jun  4 16:53:07 | PSP Boot environment  Modem Modulation Change: 0x1
Jun  4 16:53:08 | Firewall NAT service started
Jun  4 16:53:08 | rshaper is not enabled in the bootloader environment.
Jun  4 16:53:08 | Bridge Created: br0
Jun  4 16:53:10 | Bridge Created: br1
Jun  4 16:53:11 | Bridge Created: br2
Jun  4 16:53:13 | Bridge Interface Added: eth0
Jun  4 16:53:15 | Add Bridge Iface Error: 1
Jun  4 16:53:15 | crond 2.3.2 dillon, started, log level 8 
Jun  4 16:53:17 | DSL Carrier is down
Jun  4 16:53:47 | DSL Carrier is up
Jun  4 16:53:47 | sar read trained mode (5)(ADSL_2plus)
Jun  4 16:53:48 | ---}}} Start of connection delayed for 6 sec
Jun  4 16:53:54 | PPPoE Launch after conn delay timeout ...
Jun  4 16:53:55 | pppd 2.4.1 started by root, uid 0

I am trying to get solution for this problem for 10 days, but without success

Thank you

Pondera · Post by **Pondera** » Sun Aug 12, 2007 10:47 am

Who is your ISP (8,35 is in Italy!)?!?
I had your same problem with Alice Telecom when I subscribed it.
It is a ISP problem that they HAVE to solve!

exploit · Post by **exploit** » Sun Aug 12, 2007 11:14 am

Its in Bosnia, but why then DSL-300T with firmware from JackTheVendicator (1.5 highreliability) is working?

Post by **thechief** » Sun Aug 12, 2007 3:28 pm

What is the output of these commands (from the Dlink and JackTheVendicator firmwares)?

Code: Select all

cat /proc/avalanche/avsar_ver
cat /proc/modules

exploit · Post by **exploit** » Sun Aug 12, 2007 9:37 pm

Here are outputs from

cat /proc/avalanche/avsar_ver
cat /proc/modules

DSL-300T (JackTheVendicator's firmware):

Code: Select all

*********************************************************
*           ADSL ROUTER ACORP LAN120 USB/LAN            *
*          Ported to 30xT by JackTheVendicator          *
*             <jackthevendicator@gmail.com>             *
*********************************************************


BusyBox v1.2.0 (2006.07.18-00:49+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# cat /proc/avalanche/avsar_ver
ATM Driver version:[7.00.01.00]
DSL HAL version: [7.00.01.00]
DSP Datapump version: [7.00.04.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]
# cat /proc/modules
tiatm                 134216   1
#

DSL-320T (V3.10B01T01.EU.20070523):

Code: Select all

BusyBox v0.61.pre (2007.05.23-15:51+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# cat /proc/avalanche/avsar_ver
ATM Driver version:[7.00.01.00]
DSL HAL version: [7.00.01.00]
DSP Datapump version: [7.00.04.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
# cat /proc/modules
tiatm                 134600   1
#

DSL-320T (RT 2.3):

Code: Select all

*********************************************************
*   ROUTERTECH AR7RD ADSL ROUTER (LAN, 1-PORT, USB)     *
*********************************************************


BusyBox v0.61.pre (2007.06.04-15:53+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/var # cat /proc/avalanche/avsar_ver
ATM Driver version:[6.01.03.00]
DSL HAL version: [6.01.02.00]
DSP Datapump version: [6.02.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
/var # cat /proc/modules
avalanche_usb          63296   0 (unused)
tiatm                 133520   1
/var #

TNX

Post by **thechief** » Sun Aug 12, 2007 10:22 pm

Both Dlink and JackTheVendicator have the same DSP and ATM drivers (7.00.x). That would seem to be the key - perhaps Dlink-specific versions of those drivers are being used.

exploit · Post by **exploit** » Sun Aug 12, 2007 10:48 pm

OK, So is there anything I can do? Is there any firmware with 7.00.x drivers?

Thank you

Post by **thechief** » Mon Aug 13, 2007 5:55 am

exploit wrote:I can do? Is there any firmware with 7.00.x drivers?

You only have that option with wireless routers and non-wireless routers with 4mb flash.

exploit · Post by **exploit** » Mon Aug 13, 2007 9:53 am

I think thats not problem. I found firmware which uses 7.0.x drivers:

DSL-320T_McMcc_1_1_00_RU_20070424_20070727_DSP70_ZA

Code: Select all

*********************************************************
*           ADSL ROUTER D-LINK DSL-320T                 *
*********************************************************


BusyBox v0.61.pre (2007.06.19-18:02+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# cat /proc/avalanche/avsar_ver
ATM Driver version:[7.00.01.00]
DSL HAL version: [7.00.01.00]
DSP Datapump version: [7.00.04.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
# cat /proc/modules
rshaper                 7808   0 (unused)
tiatm                 134600   1
#

And again PPOE is not working

Post by **mstombs** » Mon Aug 13, 2007 10:50 am

It seems that pppoe is always LLC encapsulation so you don't get a choice of VC-MUX, but I think PAP/CHAP still applies, suggest you try either/both rather than auto.

Also I wonder if the default 'keep alive'/'connect on demand' is the same it seems your DSL connects but not the PPPOE have you tried toggling all and reconnecting?

exploit · Post by **exploit** » Mon Aug 13, 2007 11:46 am

I tried both PAP/CHAP and auto, and nothing.

But if I set it "on demand" I got following results on system log:

Code: Select all

Description  	 	Type  	 	IP  	 	State  	 	Online  	 	Disconnect Reason
ConnectionADSL 	pppoe 	N/A 	Not Connected 	0 	Can Not Reach PPP Server


Sep 16 12:00:08 | Valid Configuration Tree
Sep 16 12:00:08 | NTP Polling Timer for DHCP Started succesfully.
Sep 16 12:00:08 | DSL Polling Timer Started succesfully.
Sep 16 12:00:08 | PSP Boot environment  Modem Modulation Change: 0x3
Sep 16 12:00:09 | Firewall NAT service started
Sep 16 12:00:09 | Bridge Created: br0
Sep 16 12:00:10 | Bridge Created: br1
Sep 16 12:00:12 | Bridge Interface Added: eth0
Sep 16 12:00:18 | DSL Carrier is down
Sep 16 12:00:38 | DSL Carrier is up
Sep 16 12:00:38 | sar read trained mode (1)(ADSL_G.dmt)
Sep 16 12:00:39 | ---}}} Start of connection delayed for 22 sec
Sep 16 12:01:01 | PPPoE Launch after conn delay timeout ...
Sep 16 12:01:02 | pppd 2.4.1 started by root, uid 0
Sep 16 12:01:02 | MRU: 1500
Sep 16 12:01:02 | PPPoE Connect with IP Address 10.64.64.64 
Sep 16 12:01:02 | PPPoE Connection Successfully Established 
Sep 16 12:01:02 | PPPoE Connect with Gateway IP Address: 10.112.112.112 
Sep 16 12:01:02 | local  IP address 10.64.64.64
Sep 16 12:01:02 | remote IP address 10.112.112.112
Sep 16 12:01:02 | dproxy force reload config.

10.0.0.0. - 10.255.255.255 are private IP addresses, and its not working again...

Post by **thechief** » Mon Aug 13, 2007 5:08 pm

exploit wrote:I think thats not problem. I found firmware which uses 7.0.x drivers:

DSL-320T_McMcc_1_1_00_RU_20070424_20070727_DSP70_ZA

If that is not the problem, then the only things I can think of are:
1. some different settings in config.xml, or
2. some different kernel settings

The second is impossible to investigate. The first can be investigated by comparing all the different /etc/config.xml files.

What are the "Gateway" versions in the Dlink and JackTheVendicator firmwares? You can find this in the Status->Product information menu.

Post by **mstombs** » Mon Aug 13, 2007 9:02 pm

If you google for those local IP addresses you see they are quite common 'linux defaults'. One extra suggestion is the modem MAC address may be being restricted by your ISP - but I don't know why D-Link firmware would behave differently. The MAC address used by Routertech and similar firmware is given by the env variable HWA_3 I believe.