Router Upgrade Check 1.3.7 25/02/2010 19:45:15 Router IP: 192.168.1.1 CLI is needed Description: Dlink G604T Board type: AR7WRD Product ID: AR7WRD Bootloader: pspboot RAM 16.0 MB Flash (ROM) 4.0 MB ADAM2: No No default env: No Linux version: 2.4.17_mvl21-malta-mips_fp_le Firmware build: Firmware version: V1.00B02T02.UK.20040618 Firmware stamp: 20040618190403 CPU: MIPS 4KEc V4.8 DSP: 1.01.00.00 Annex: A /proc/wlan: No /usr/sbin/wlan: No TIAP: Yes TNETW: No Wireless: Yes WIFI chip: TNETW1130 WIFI chip conf: No Ports: 4 Marvell (or Marvell like): No NSP: V1.00B02T02.UK.20040618 Manufacturers: D-link Corporation RNDIS: HRNDIS: WARNING Cannot confirm the model number of the wireless chip. The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again. Warning! Core Logic (NSP) could not be read. If the Core Logic version is too low you may need to upgrade to your router manufacturer's latest firmware first. WARNING Your router does not have a Marvell switch and so your switch is not supported. Your Ethernet ports may or may not function correctly with a RouterTech firmware. Select an AR7WRD PSPBOOT 4 PORT firmware. Latest: routertech-ar7wrd-pspboot-firmware-20100105.zip Please read the instructions that come with the firmware files before you upgrade. With your current MTD values, you have to upgrade your firmware using separate firmware image files. You may be able to use a single image, provided you create mtd4 between 0x90020000,0x90400000 /etc /versions CUSTOMER=DLinkUK MODEL=DSL-G604T VERSION=V1.00B02T02.UK.20040618 HTML_LANG=EN BOARD=AR7WRD VERSION_ID=UK CPUARCH_NAME=AR7 MODEL_ID=604 FSSTAMP=20040618190403 # # /proc/wlan cd: can't cd to /proc/wlan # # /usr/sbin/wlan cd: can't cd to /usr/sbin/wlan # # /proc/ticfg/env memsize 0x01000000 flashsize 0x00400000 modetty0 38400,n,8,1,hw modetty1 38400,n,8,1,hw bootserport tty0 cpufrequency 150000000 sysfrequency 125000000 bootloaderVersion 0.22.02 ProductID AR7WRD HWRevision Unknown SerialNumber none my_ipaddress 10.48.88.66 maca 00:0F:3D:BA:A1:93 usb_vid 0x0 usb_pid 0x0 usb_rndis_mac 00.0d.88.11.03.02 usb_board_mac 00.0d.88.22.03.02 usb_man N/A usb_prod N/A usb_serial 1234567890 prompt Adam2_AR7RD firstfreeaddress 0x9401d328 req_fullrate_freq 125000000 mtd0 0x900a0000,0x903f0000 mtd1 0x90010000,0x900a0000 mtd2 0x90000000,0x90010000 mtd3 0x903f0000,0x90400000 autoload 1 mac_ap 00:0F:3D:BA:A1:94 # # /proc/sys/dev/adam2/environment /proc/version Linux version 2.4.17_mvl21-malta-mips_fp_le (jordan@Jordan_Linux) (gcc version 2.95.3 20010315 (release/MontaVista)) #60 ¶g /proc/cpuinfo processor : 0 cpu model : MIPS 4KEc V4.8 BogoMIPS : 149.91 wait instruction : no microsecond timers : yes extra interrupt vector : yes hardware watchpoint : yes VCED exceptions : not available VCEI exceptions : not available # # /proc/avalanche/avsar_ver ATM Driver version:[4.01.00.00] DSL HAL version: [1.01.00.00] DSP Datapump version: [1.01.00.00] Annex A SAR HAL version: [01.06.06] PDSP Firmware version:[0.49] # # /proc/interrupts 7: 18436 R4000 timer/counter [MIPS interrupt] 15: 112 serial [hw0 (Avalanche Primary)] 23: 0 + SAR [hw0 (Avalanche Primary)] 29: 1526 + VLYNQ0 [hw0 (Avalanche Primary)] 41: 717 + Cpmac Driver [hw0 (Avalanche Primary)] 47: 3 + DSL [hw0 (Avalanche Primary)] # # /proc/modules tiwlan 67816 2 ip_nat_talk 3080 0 (unused) ip_conntrack_talk 2908 2 ip_nat_tftp 2280 0 (unused) ip_conntrack_tftp 2204 1 ip_nat_irc 3224 0 (unused) ip_conntrack_irc 3836 1 ip_nat_h323 3344 0 (unused) ip_conntrack_h323 3068 1 ip_nat_ftp 4056 0 (unused) ip_conntrack_ftp 5004 1 ipt_multiport 972 0 (unused) ipt_REDIRECT 1044 0 (unused) ipt_limit 1356 0 (unused) ipt_TCPMSS 2956 0 (unused) ipt_state 920 0 (unused) ipt_MASQUERADE 1684 0 (unused) iptable_nat 22856 6 [ip_nat_talk ip_nat_tftp ip_nat_irc ip_nat_h323 ip_nat_ftp ipt_REDIRECT ipt_MASQUERADE] iptable_filter 2076 0 (unused) ip_conntrack 29648 8 [ip_nat_talk ip_conntrack_talk ip_nat_tftp ip_conntrack_tftp ip_nat_irc ip_conntrack_irc ip_nat_h323 ip_conntrack_h323 ip_nat_ftp ip_conntrack_ftp ipt_REDIRECT ipt_state ipt_MASQUERADE iptable_nat] ip_tables 14656 10 [ipt_multiport ipt_REDIRECT ipt_limit ipt_TCPMSS ipt_state ipt_MASQUERADE iptable_nat iptable_filter] bridge 29456 1 tiatm 113704 0 (unused) # # /proc/flashinfo cat: /proc/flashinfo: No such file or directory # # logic:status/nspver V1.00B02T02.UK.20040618 # logic:status/has_marvell # /etc /led.conf # Configuration File for AR7WRD board # List of LEDS controllable through led module # led no 3 -> DSL(DSP) # led no 4 -> DSL(DSP) # led no 5 -> GPIO13 # led no 7 -> GPIO12 # led no 8 -> GPIO10 # led no 9 -> GPIO9 # led no 10 -> GPIO8 # led no 11 -> GPIO7 # led no 12 -> GPIO6 # led no 13 -> GPIO15 # led no 14 -> GPIO16 # Led numbers from left to right on AR7WRD Board # NON MULTIPLEXED MODE #Position-> x x x x x #Led No-> HW 4 5 7 12 #Usage-> Pwr DSL PPP USB WIFI ################################################################## module = 1 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb state = 1 # 1 = idle , 2 = training, 3 = sync , 4 = activity led = 4 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 2 # 1 = idle , 2 = training, 3 = sync , 4 = activity led = 4 # led number mode = 5 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 200 # blink/flash rate in ms state = 3 # 1 = idle , 2 = training, 3 = sync , 4 = activity led = 4 # led number mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 4 # 1 = idle , 2 = training, 3 = sync , 4 = activity led = 4 # led number mode = 3 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 25 # blink/flash rate in ms ################################################################## module = 2 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb state = 1 # 1 = no_pppd_session , 2 = pppd_session led = 5 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 2 # 1 = no_pppd_session , 2 = pppd_session led = 5 # led number mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink rate in ms ################################################################## # USEFUL WHEN MULTIPLEXED(ETH+USB) MODE IS SELECTED #module = 3 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb #state = 1 # 1 = idle , 2 = link, 3 = activity #led = 7 # led number #mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash #param = 0 # blink/flash rate in ms #state = 2 # 1 = idle , 2 = link, 3 = activity #led = 7 # led number #mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash #param = 0 # blink/flash rate in ms #state = 3 # 1 = idle , 2 = link, 3 = activity #led = 7 # led number #mode = 2 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash #param = 20 # blink/flash rate in ms ################################################################## # USEFUL WHEN NON MULTIPLEXED MODE IS SELECTED module = 5 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb state = 1 # 1 = idle , 2 = link, 3 = activity led = 7 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 2 # 1 = idle , 2 = link, 3 = activity led = 7 # led number mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 3 # 1 = idle , 2 = link, 3 = activity led = 7 # led number mode = 3 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 20 # blink/flash rate in ms ################################################################## # USEFUL WHEN NON MULTIPLEXED MODE IS SELECTED module = 6 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb state = 1 # 1 = idle , 2 = link, 3 = activity led = 8 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 2 # 1 = idle , 2 = link, 3 = activity led = 8 # led number mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 3 # 1 = idle , 2 = link, 3 = activity led = 8 # led number mode = 3 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 20 # blink/flash rate in ms ################################################################## module = 4 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb state = 1 # 1 = idle , 2 = link, 3 = activity led = 12 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 2 # 1 = idle , 2 = link, 3 = activity led = 12 # led number mode = 4 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 3 # 1 = idle , 2 = link, 3 = activity led = 12 # led number mode = 3 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 40 # blink/flash rate in ms ################################################################## module = 9 # 1 = adsl 2 = pppoe 3 = lan 4 = wifi 5 = usb 9 = STATUS state = 1 # 1 = normal, 2 = halt led = 9 # led number mode = 5 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 500 # blink/flash rate in ms state = 2 # 1 = normal, 2 = halt led = 9 # led number mode = 1 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 0 # blink/flash rate in ms state = 3 # 1 = normal, 2 = halt led = 9 # led number mode = 3 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 40 # blink/flash rate in ms state = 4 # 1 = normal, 2 = halt led = 9 # led number mode = 2 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 40 # blink/flash rate in ms state = 5 # 1 = normal, 2 = halt led = 9 # led number mode = 5 # 1 = off,2 = blinkon,3 = blinkoff,4 = on,5 = Flash param = 40 # blink/flash rate in ms