NO Wireless in AZtech DSL605EW .

Specific forum for all wireless related issues. Even if you have a wireless router, only post here if you have a question about issues with the wireless functionality of it. Questions about wireless access points, cards, hot-spots etc. are also welcome here.
Post Reply
comprishi
Novice
Novice
Posts: 10
Joined: Thu Sep 09, 2010 5:39 pm

NO Wireless in AZtech DSL605EW .

Post by comprishi » Fri Sep 10, 2010 3:07 am

Router Upgrade Check 1.4.0 10/09/2010 07:47:05
Router IP: 192.168.1.1
Description: Aztech DSL 605EW (Asian, Dual Antenna)
Board type: AR7WRD
Product ID: AR7WRD
Bootloader: psbl
RAM 16.0 MB
Flash (ROM) 4.0 MB
ADAM2: No
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build: RouterTech_3.7.1B_1350A_20100408_2.93_AR7WRD_psbl
Firmware version: 1350A_20100408
Firmware stamp: 20100408093745
CPU: MIPS 4KEc V4.8
DSP: 7.01.01.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: Yes
TIAP: No
TNETW: No
Wireless: Yes
WIFI chip: TNETW1130
WIFI chip conf: No
Ports: 4
Ports (according to router): 4
Marvell (or Marvell like): Yes
NSP: 3.7.1B
Manufacturers: Siara Systems Inc
RNDIS: Telogy Networks Inc
HRNDIS: Telogy Networks Inc
NOTE: Only use version 2.9 or later of the RouterTech firmware for your router.
WARNING
Cannot confirm the model number of the wireless chip.
The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again.

Select an AR7WRD PSPBOOT 4 PORT firmware.
Latest: routertech-ar7wrd-pspboot-firmware-4ports-20100818.zip
Please read the instructions that come with the firmware files before you upgrade.
According to your current MTD values, you should be able to upgrade using a single firmware image.

/etc /versions
BUILD=RouterTech_3.7.1B_1350A_20100408_2.93_AR7WRD_psbl
VERSION=1350A_20100408
BOARD=AR7WRD
FSSTAMP=20100408093745

/proc/wlan
-sh: cd: can't cd to /proc/wlan

/usr/sbin/wlan
/usr/sbin/wlan #
/proc/ticfg/env
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
IPA 192.168.1.1
MAC_PORT 0
MEMSZ 0x01000000
FLASHSZ 0x00400000
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
BOOTCFG m:f:"mtd1"
mtd2 0x90000000,0x90010000
autoload 1
autoload_timeout 25
memchk.sh 1
checksync.sh 1
cron_la.sh 2
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90400000
autopvc_enable 1
vlynq_polarity low
pppoe_relay_enabled 1
DSL_BIT_TMODE 1
sar_ipacemax 6
DSL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_vid 0x0451
usb_pid 0x6060
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
mtd0: 0x900AF000,
mtd1: 0x90020090,
mtd2: 0x90000000,
mtd3: 0x90010000,
mtd4: 0x90020000,
IPA_SVR 192.168.1.2
MODETTY0 38400,n,8,1,hw
MODETTY1 38400,n,8,1,hw
StaticBuffer 120
configid 3
PROMPT psbl>
WLAN_HWADDR0 00:1d:7e:ac:ec:f7
wan_br_mac 00:1d:7e:ac:ec:f7
mtd1 0x90020090,0x900a0000
mtd0 0x900a0000,0x90400000
modulation 0x24ff
connection1-mac 00-30-88-10-c0-a6
cron_enable 1
led_conf led.wa1003a
NVS_TFTP_LOAD 1
connection1 0x502c

/proc/sys/dev/adam2/environment
cat: can't open '/proc/sys/dev/adam2/environment': No such file or directory

/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers@RouterTech.Org) #143 Thu Apr 8 09:33:35 BST 2010

/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available

/proc/avalanche/avsar_ver
ATM Driver version:[7.01.00.10]
DSL HAL version: [7.01.00.08]
DSP Datapump version: [7.01.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]

/proc/interrupts
7: 181497 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 2731 serial [hw0 (Avalanche Primary)]
23: 4962 + SAR [hw0 (Avalanche Primary)]
27: 4147 + Cpmac Driver [hw0 (Avalanche Primary)]
29: 0 vlynq0 [hw0 (Avalanche Primary)]
31: 47 + DSL [hw0 (Avalanche Primary)]

/proc/modules
tiatm 135360 c0023060 96 2

/proc/flashinfo
Flash type: AMD; Manufacturer=AMD.
Manufacturer_ID=0x0001; Chip_ID=0x007E; Chip_Size=0x400000; Erase_Regions=0x0002

/etc/PORTS
4

logic:status/nspver
3.7.1B /usr/sbin/wlan

logic:status/has_marvell
1

/etc /led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
##################################################################
# The GPIO numbers 0 to 31 ==> correspond to GPIO pins #########
# The GPIO numbers 32,33 are mapped to ADSL (LED) pins ###########
##################################################################
module = adsl # module = {adsl,usb,pppoe,wlan}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 200 # flash on duration in ms
param2 = 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 150 # blink/flash rate in ms ,orig = 25
######################################################################
module = cpmac # module = {adsl,usb,pppoe,wlan,cpmac}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 7 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 7 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 7 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 7 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
#################################################
module = usb # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = wlan # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 150 # blink/flash rate in ms ,orig = 100
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 150 # blink/flash rate in ms ,orig = 100
######################################################################

module = status # module = {adsl,usb,pppoe, status}
state = 0 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 500 # flash on duration in ms
param2 = 500 # flash off duration in ms
i
comprishi
Novice
Novice
Posts: 10
Joined: Thu Sep 09, 2010 5:39 pm

Re: NO Wireless in AZtech DSL605EW .

Post by comprishi » Fri Sep 10, 2010 3:15 am

I have recently installed routertech firmware 2.94 after my router was bricked. So i did not got chance to save the environment and configuration of the router.
Now after i have installed the routertech firmware every thing is ok but the wireless doesnot work.And the wireless led also doesnot work eventhough i have enabled Wireless AP in the web interface.
please help
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12067
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: NO Wireless in AZtech DSL605EW .

Post by thechief » Fri Sep 10, 2010 5:37 pm

The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
User avatar
notinthisworld
Experienced
Experienced
Posts: 159
Joined: Wed Feb 27, 2008 11:28 am

Re: NO Wireless in AZtech DSL605EW .

Post by notinthisworld » Sun Sep 12, 2010 3:31 pm

comprishi wrote:I have recently installed routertech firmware 2.94 after my router was bricked. So i did not got chance to save the environment and configuration of the router.
Now after i have installed the routertech firmware every thing is ok but the wireless doesnot work.And the wireless led also doesnot work eventhough i have enabled Wireless AP in the web interface.
please help
after clicking apply on the wireless setup, did you click the restart access point?
Image
Post Reply