Somebody Help me please
Somebody Help me please
Hello everyone.....at first sorry i have bad englis
i have problem in my router when i try to upgrade it ....i choosed wrong firmware and then it become BRICK
I did tryed PCtool ...and read most problems in this website
anyway when i used pc tools ...finally it's worked but when i restart my pc ...it's back to same problem Brick...
i tryed to flash it again and it's successfully ...and i choosed the orginal firmware.....all steps is in the pics ....may anyone tell me what's wrong and help me .
i forgot to say my router is D-LINK ADSL-2540T
[/img]
i have problem in my router when i try to upgrade it ....i choosed wrong firmware and then it become BRICK
I did tryed PCtool ...and read most problems in this website
anyway when i used pc tools ...finally it's worked but when i restart my pc ...it's back to same problem Brick...
i tryed to flash it again and it's successfully ...and i choosed the orginal firmware.....all steps is in the pics ....may anyone tell me what's wrong and help me .
i forgot to say my router is D-LINK ADSL-2540T
[/img]
You have a pspboot router, and have probably loaded an adam2 firmware and configuration which has wiped your environment section, and the bootloader has recreated the minimum on reboot.
You should have a backup of the environment in the "Router Upgrade Checker" RUC log, there's an example here for a 'similar router'
viewtopic.php?t=1413
You should have a backup of the environment in the "Router Upgrade Checker" RUC log, there's an example here for a 'similar router'
viewtopic.php?t=1413
(thank goodness there are forums like this)
many thanks to SyBorg &mstombs
like i said before
i can't get into or ping my router.....and i did read that pages u sent to me
sorry to say that but i don't know what to do...so plz tell me what to do
step by step ...cuz it's hardly to know what they mean cuz i don't speak english
i'm using dectionary to trans most the words...i'm just know some english from high school lol
This is more information of my router
1. What is the specific name and model of your router
D-Link DSL-2540T
2. What was your router's firmware version before upgrading
DLinkEU-A_DSL-2540T_singleimage_kernel_fs_V3.02B01T01.EU-A.20061220
3. What bootloader (and bootloader version) does your router have
PSPBoot 1.3.7.15 for 4M/16M AR7RD
4.What was the specific RouterTech firmware file that you tried to upgrade to
routertech-ar7rd-adam2-4ports-firmware-20080723\annexb
And it's worked with me just 1 time and whn I restarted my router …I got that problem router is not response?
5.Was the upgrading done via ethernet or wireless connection
Ethernet
6-Was the upgrading done via the web interface or via the PC Tool or some other tools
webinterface
7. Was there any error or problem while you were trying to upgrade the firmware:
no
8. If so, what was the specific error/problem, and what did you do to try to overcome it:
9. Did you reset the router to factory defaults after upgrading:
i don't remember
10. Describe in detail the current state of your router:
i don't know twhatr this question mean because i don't speak english
but i can say ...the light of my router is power on ,LAN on, status off,ADSL OFF,
11. If you switch the router off for about 5 minutes, and switch it on again, what happens:
nothing
AND this is the information of my router
Release Image Filename: DLinkEU-A_DSL-2540T_singleimage_kernel_fs_V3.02B01T01.EU-A.20061220
Bootloader Version: PSPBoot 1.3.7.15 for 4M/16M AR7RD
Firmware Version: V3.02B01T01.EU-A.20061220
Hardware Version: V.A1
Hardware Compatibility: TI 7300EZ + 1350AZ
Software Compatibility: NSP 3.6.1 + PSP4.6
ADSL Compatibility: ATM Driver 6.00.01.00 with Datapump 6.00.04.00 Annex A
General Description: ADSL2+ Router with 4-port switch
LAN interface IP: 192.168.1.1
WAN interfaces:
1. PVC0: PPPoE LLC VPI/VCI= 8/35
System:
Username/Password: admin/admin
Username1/Password1: user/user
DHCP Server: Enabled
UPnP: Disabled
DNS: Enabled
and this is pics to expalain my problem
and i think it's claer
i can't get into my router or ping it.
SO please i want to know what to do step by step ...how to make my router work on orginal firmware or routertech firmware ...and which programs or tools use to repair my router
thanks for help:)
many thanks to SyBorg &mstombs
like i said before
i can't get into or ping my router.....and i did read that pages u sent to me
sorry to say that but i don't know what to do...so plz tell me what to do
step by step ...cuz it's hardly to know what they mean cuz i don't speak english
i'm using dectionary to trans most the words...i'm just know some english from high school lol
This is more information of my router
1. What is the specific name and model of your router
D-Link DSL-2540T
2. What was your router's firmware version before upgrading
DLinkEU-A_DSL-2540T_singleimage_kernel_fs_V3.02B01T01.EU-A.20061220
3. What bootloader (and bootloader version) does your router have
PSPBoot 1.3.7.15 for 4M/16M AR7RD
4.What was the specific RouterTech firmware file that you tried to upgrade to
routertech-ar7rd-adam2-4ports-firmware-20080723\annexb
And it's worked with me just 1 time and whn I restarted my router …I got that problem router is not response?
5.Was the upgrading done via ethernet or wireless connection
Ethernet
6-Was the upgrading done via the web interface or via the PC Tool or some other tools
webinterface
7. Was there any error or problem while you were trying to upgrade the firmware:
no
8. If so, what was the specific error/problem, and what did you do to try to overcome it:
9. Did you reset the router to factory defaults after upgrading:
i don't remember
10. Describe in detail the current state of your router:
i don't know twhatr this question mean because i don't speak english
but i can say ...the light of my router is power on ,LAN on, status off,ADSL OFF,
11. If you switch the router off for about 5 minutes, and switch it on again, what happens:
nothing
AND this is the information of my router
Release Image Filename: DLinkEU-A_DSL-2540T_singleimage_kernel_fs_V3.02B01T01.EU-A.20061220
Bootloader Version: PSPBoot 1.3.7.15 for 4M/16M AR7RD
Firmware Version: V3.02B01T01.EU-A.20061220
Hardware Version: V.A1
Hardware Compatibility: TI 7300EZ + 1350AZ
Software Compatibility: NSP 3.6.1 + PSP4.6
ADSL Compatibility: ATM Driver 6.00.01.00 with Datapump 6.00.04.00 Annex A
General Description: ADSL2+ Router with 4-port switch
LAN interface IP: 192.168.1.1
WAN interfaces:
1. PVC0: PPPoE LLC VPI/VCI= 8/35
System:
Username/Password: admin/admin
Username1/Password1: user/user
DHCP Server: Enabled
UPnP: Disabled
DNS: Enabled
and this is pics to expalain my problem
and i think it's claer
i can't get into my router or ping it.
SO please i want to know what to do step by step ...how to make my router work on orginal firmware or routertech firmware ...and which programs or tools use to repair my router
thanks for help:)
I'm guessing the you didn't follow the instructions to run the Router Upgrade Checker before you started?
I think it would be best for you to ensure you have the original firmware for your router from the manufacturer and then read the instructions here viewtopic.php?t=335 in order to load that firmware back on to the router. If you can recover it then start again with the RUC.
I think it would be best for you to ensure you have the original firmware for your router from the manufacturer and then read the instructions here viewtopic.php?t=335 in order to load that firmware back on to the router. If you can recover it then start again with the RUC.
We learn something every day, and lots of times it’s that what we learned the day before was wrong.
—Bill Vaughan
—Bill Vaughan
There's quite a few variables missing from your environment, the important ones I can see by comparing with xbipin's in the link above (running the same D-Link firmware) are
This leaves room for a mtd5 0x903e0000,0x90400000, which could be useful later.
You should connect using the PC-Tool as in your first post then add these variables. Then reboot the router and try reloading the firmware again. The router should then run, but there are extra variables such as MAC addresses that should be added to fully restore the original setup.
Code: Select all
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
autoload 1
autoload_timeout 7
BOOTCFG m:f:"mtd1"
mtd4 0x90020000,0x903e0000
mtd0 0x900b1000,0x903e0000
mtd1 0x90020090,0x900b1000
You should connect using the PC-Tool as in your first post then add these variables. Then reboot the router and try reloading the firmware again. The router should then run, but there are extra variables such as MAC addresses that should be added to fully restore the original setup.
my router work again
finaalyyy it's work ... thank SyBorg and special thanks to mstombs my router is work cuz i used that variables u gave to me .... it's not took even 5 mins ....i'm really happy ...i don't know how thank u .... sorry for my bad english.... but i didn't used that variable of mtd5 cuz i didn't undrestand what u mean
cuz i don't know how to use it later ...and i don't want to ruin my router again lool .....anyway ...thank youuuuuuu very muchThis leaves room for a mtd5 0x903e0000,0x90400000, which could be useful later.