Hello,
I installed some months ago a firmware 2.94 - it worked for many weeks without pbs.
Now it stopped working - no adsl connection and reboots every 3 minutes
I erased configuration and tried to write it again
this is the LOG
Aug 18 11:18:11 | AP is disabled
Aug 18 11:18:11 | Valid Configuration Tree
Aug 18 11:18:11 | NTP Polling Timer for DHCP Started succesfully.
Aug 18 11:18:11 | DSL Polling Timer Started succesfully.
Aug 18 11:18:11 | PSP Boot environment Modem Modulation Change: 0xff
Aug 18 11:18:11 | Firewall NAT service started
Aug 18 11:18:12 | Bridge Created: br0
Aug 18 11:18:13 | Bridge VLAN0 add eth0
Aug 18 11:18:13 | Bridge VLAN AUTO OFF.
Aug 18 11:18:13 | Bridge VLAN0 add eth1
Aug 18 11:18:13 | Bridge VLAN AUTO OFF.
Aug 18 11:18:13 | Bridge VLAN0 add eth2
Aug 18 11:18:13 | Bridge VLAN AUTO OFF.
Aug 18 11:18:13 | Bridge VLAN0 add eth3
Aug 18 11:18:13 | Bridge VLAN AUTO OFF.
Aug 18 11:18:13 | Bridge Created: br1
Aug 18 11:18:15 | Bridge Created: br2
Aug 18 11:18:17 | Bridge Interface Added: eth0
Aug 18 11:18:19 | Bridge Interface Added: eth1
Aug 18 11:18:22 | Bridge Interface Added: eth2
Aug 18 11:18:23 | Bridge Interface Added: eth3
Aug 18 11:18:25 | USB is disabled
Aug 18 11:18:25 | rcS not stopped by init. Stopping it ...
Aug 18 11:18:25 | DSL Carrier is down
Aug 18 11:18:27 | no servers found in /etc/resolv.conf, will retry
and this is the environment
System environment (/proc/sys/dev/adam2/environment)
autoload 1
autoload_timeout 25
bootloaderVersion 0.22.02
bootserport tty0
checksync.sh 1 20
connection1 0xc4c4
cpufrequency 150000000
cron_enable 1
firstfreeaddress 0x9401d328
flashsize 0x00400000
http_port 7777
HWRevision A1
ip1.sh ;/usr/sbin/dropbear -i -a -p 2222
ip2.sh ;/sbin/iptables -I INPUT -i ppp0 -p tcp --dport 7777 -j ACCEPT
ip3.sh ;/sbin/iptables -I INPUT -i ppp0 -p tcp --dport 2222 -j ACCEPT
led_conf led.g604t
maca 00:11:95:9D:5C:3B
mac_ap 00:11:95:9D:5C:3C
memchk.sh 1
memsize 0x01000000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
modulation 0xff
mtd0 0x9008f000,0x903f0000
mtd1 0x90010090,0x9008f000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
my_ipaddress 192.168.1.1
ProductID ARWRD
prompt Adam2_AR7RD
req_fullrate_freq 125000000
SerialNumber DR6C158004471
StaticBuffer 120
sysfrequency 125000000
usb_board_mac 00.0d.88.22.03.02
usb_man N/A
usb_pid 0x0
usb_prod N/A
usb_rndis_mac 00.0d.88.11.03.02
usb_serial 1234567890
usb_vid 0x0
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
someone has ideas? I already defragmented the environment
Thx
paolo
2.94 stopped working (continuos reboot)
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: 2.94 stopped working (continuos reboot)
Try this
Code: Select all
unsetenv checksync.sh && /sbin/reboot
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: 2.94 stopped working (continuos reboot)
It doesn't continuosly reboot anymore.
I'll check if I can get syncronisation (lately it was impossible but probably a consequence of rebooting)
I understand I can't use checksync.sh anymore?
Thx,
Paolo
I'll check if I can get syncronisation (lately it was impossible but probably a consequence of rebooting)
I understand I can't use checksync.sh anymore?
Thx,
Paolo
Paolo
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: 2.94 stopped working (continuos reboot)
You need to find out why you're not getting a connection. Until that is sorted out, checksync will only keep doing what it is supposed to do - check for a connection, and reboot if there isn't one.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: 2.94 stopped working (continuos reboot)
I confirm I can't get the adsl
log says DSL is down, but adsl works with other modems.
I believe a hardware pb...
Paolo
log says DSL is down, but adsl works with other modems.
I believe a hardware pb...
Paolo
Paolo
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: 2.94 stopped working (continuos reboot)
Very likely.tiepolo wrote:I believe a hardware pb...
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.