RUC says old firmware for Huawei Quidway Wa1003a

[thechief]

Post the system diagnostics ("Tools" menu).

[harimkb]

here is the System Diagnostics report of my router Huawei Wa1003a

ROUTERTECH SYSTEM DIAGNOSTICS

Client browser information
Mozilla/5.0 (Windows NT 6.1; WOW64; rv:8.0) Gecko/20100101 Firefox/8.0

Router operating system version
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #1 Mon May 2 01:14:30 BST 2011

Firmware version information
BUILD=RouterTech_3.6.0D_20110502_2.96
VERSION=3.6.0D-RouterTech-Adam2
BOARD=AR7WRD
TARGET=Adam2_1-Port
FSSTAMP=20110502011811
ROHS=0

Wireless version information
5.7.0.6, 1/4/2005

Wireless chip information
-------- ConfigOptionsFixed ----------
NVSVersion = 02 41 01 00 ffffffcd 01 ffffffb1 6b
ProductId =
ManufactureId =
dot11MacAddress = 01:04:00:11:00:00
ProbeDelay = 257
EndofMemory = 0x6010500
dot11CCAModeSupported = 0
dot11DiversitySupport = 2
dot11ShortPreambleOptionImplemented = 1
dot11PBCCOptionImplemented = 2
dot11ChanneAgilityPresent = 1
dot11PHYType = 2
dot11TempType = 30
-------- ACX100 elements ----------
AntennaList (0) =
SupportedPowerLevels (0) =
SupportedDataRates (0) =
SupportedRegDomains (0) =


PSP version information

Linux OS DSL-PSPOhioL version 4.5.0.5 Best and Final on BasePSP Version 5.7.6.12 May 2 2011 01:15:31
Avalanche SOC Version: 0x20005 operating in cached, write back, write allocate mode
Cpu Frequency:150 MHZ
System Bus frequency: 125 MHZ


Driver version information
Core Logic version: 3.6.0D
Texas Instruments CPMAC driver version: 1.5
Texas Instruments CPMAC HAL version: CPMAC 01.07.08 May 2 2011 01:14:41
ATM Driver version:[7.05.01.00]
DSL HAL version: [7.05.01.00]
DSP Datapump version: [7.05.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]

Modem Modulation Information
NO_MODE 0x0
ADSL_G.dmt 0x3
ADSL_G.lite 0x4
ADSL_G.dmt.bis 0x8
ADSL_G.dmt.bis_DELT 0x9
ADSL_2plus 0x10
ADSL_2plus_DELT 0x11
ADSL_re-adsl 0x20
ADSL_re-adsl_DELT 0x21
ADSL_ANSI_T1.413 0x2
MULTI_MODE 0x1
ADSL_G.dmt.bis_AnxI 0x0
ADSL_G.dmt.bis_AnxJ 0x0
ADSL_G.dmt.bis_AnxM 0x400
ADSL_2plus_AnxI 0x0
ADSL_2plus_AnxJ 0x0
ADSL_2plus_AnxM 0x2000
G.shdsl 0x0
IDSL 0x0
HDSL 0x0
SDSL 0x0
VDSL 0x0

System environment (/proc/sys/dev/adam2/environment)
cpmac_phy 0
memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
ProductID AR7DB
HWRevision none
SerialNumber none
my_ipaddress 192.168.1.199
maca 00:e0:fc:32:98:c4
prompt Adam2_AR7DB
firstfreeaddress 0x9401d888
req_fullrate_freq 125000000
mtd0 0x9008f000,0x903f0000
mtd1 0x90010090,0x9008f000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
autoload 1
autoload_timeout 7
StaticBuffer 384
usb_prod Quidway WA1003A Series DSL Modem
usb_vid 0x1110
usb_pid 0x9022
usb_serial 00:e0:fc:32:98:c5
mtd4 0x90010000,0x903f0000
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_board_mac 00:e0:fc:32:98:c5
usb_man HUAWEI
Adam2_Release 0.22.02_b03_Mar 10 2005
sbusfrequency 125000000
usb_rndis_mac 00:e0:fc:32:98:c6
modulation 0x1
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
connection1 0x3415

connection2 0x8e0b

led_conf led.wa1003a
memchk.sh 1
checksync.sh 1 20
cron_la.sh 1
cron_enable 1

CPU information
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 149.91
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available

Memory (RAM) information
total: used: free: shared: buffers: cached:
Mem: 14520320 13946880 573440 0 884736 4427776
Swap: 0 0 0
MemTotal: 14180 kB
MemFree: 560 kB
MemShared: 0 kB
Buffers: 864 kB
Cached: 4324 kB
SwapCached: 0 kB
Active: 3964 kB
Inactive: 3144 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 14180 kB
LowFree: 560 kB
SwapTotal: 0 kB
SwapFree: 0 kB

Flash memory (chip) information
Flash_type=AMD; Manufacturer=AMD.
Manufacturer_ID=0x0001; Chip_ID=0x00F9; Chip_Size=0x400000; Erase_Regions=0x0002

Mount points
/dev/mtdblock/0 / squashfs ro 0 0
none /dev devfs rw 0 0
proc /proc proc rw 0 0
ramfs /var ramfs rw 0 0

Filesystems
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev shm
nodev pipefs
nodev ramfs
minix
nodev devfs
squashfs

MTD
dev: size erasesize name
mtd0: 00361000 00010000 "mtd0"
mtd1: 0007ef70 00010000 "mtd1"
mtd2: 00010000 00002000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 003e0000 00010000 "mtd4"

Kernel modules
tiap 708536 1
tiatm 138672 1

Interrupts
7: 111136 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 731 serial [hw0 (Avalanche Primary)]
23: 26112 + SAR [hw0 (Avalanche Primary)]
27: 0 + Cpmac Driver [hw0 (Avalanche Primary)]
29: 32422 vlynq0 [hw0 (Avalanche Primary)]
47: 107 + DSL [hw0 (Avalanche Primary)]
80: 32420 TNETW1130 [hw0 (Low Vlynq)]

Devices
Character devices:
1 mem
2 pty/m%d
3 pty/s%d
4 tts/%d
5 cua/%d
10 misc
108 ppp
128 ptm
136 pts/%d
162 raw

Block devices:
7 loop
31 mtdblock

Serial port information
serinfo:1.0 driver:5.05c revision:2001-07-08
0: uart:16550A port:A8610E00 irq:15 baud:2258 tx:11024 rx:0 RTS|DTR
1: uart:16550A port:A8610F00 irq:16 tx:0 rx:0 RTS|DTR

Processes
PID USER VSZ STAT COMMAND
1 root 1056 S init
2 root 0 SW [keventd]
3 root 0 SWN [ksoftirqd_CPU0]
4 root 0 SW [kswapd]
5 root 0 SW [bdflush]
6 root 0 SW [kupdated]
7 root 0 SW [mtdblockd]
474 root 2300 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
475 root 2252 S /usr/bin/cm_pc
477 root 3660 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
520 root 760 S /sbin/dproxy -c /etc/resolv.conf -d
521 root 996 S /usr/sbin/wlan/wpa_authenticator
546 root 1056 S init
886 root 1064 S crond -b
1852 root 2396 S /usr/sbin/pppd plugin pppoe nas0 user bh4426628482 p
1906 root 920 S /sbin/msntp -r 2 -t 5 -p 30 -s wwv.nist.gov ntp2b.mc
1907 root 684 S /usr/sbin/udhcpd /var/tmp/udhcpd.conf
2149 root 1068 S N /bin/sh diagnostics.cgi
2150 root 2344 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
2155 root 1188 S N /usr/local/bin/diagnostics
2156 root 1060 S N sh -c /usr/local/bin/diagnostics.sh
2157 root 1124 S N /bin/bash /usr/local/bin/diagnostics.sh
2197 root 1056 R N /bin/ps

ADSL Modem information

AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
US Connection Rate: 480 DS Connection Rate: 1984
DS Line Attenuation: 13 DS Margin: 31
US Line Attenuation: 8 US Margin: 29
US Payload : 2294256 DS Payload: 14440416
US Superframe Cnt : 61699 DS Superframe Cnt: 61699
US Transmit Power : 11 DS Transmit Power: 8
LOS errors: 0 SEF errors: 0
Errored Seconds: 0 Severely Err Secs: 0
Frame mode: 3 Max Frame mode: 0
Trained Path: 1 US Peak Cell Rate: 1132
Trained Mode: 3 Selected Mode: 1
ATUC Vendor Code: 4244434D ATUC Revision: 2
Hybrid Selected: 1 Trellis: 1
Showtime Count: 1 DS Max Attainable Bit Rate: 10016 kbps
BitSwap: 1 US Max Attainable Bit Rate: n/a
Annex: AnxA psd_mask_qualifier: 0x0000
ATUC ghsVid: b5 00 42 44 43 4d a1 06
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
ATUR ghsVid: b5 00 54 53 54 43 00 00
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00

[Upstream (TX) Interleave path]
CRC: 1 FEC: 0 NCD: 0
LCD: 0 HEC: 0

[Downstream (RX) Interleave path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0

[Upstream (TX) Fast path]
CRC: 0 FEC: 0 NCD: 1
LCD: 0 HEC: 0

[Downstream (RX) Fast path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0

[ATM Stats]
[Upstream/TX]
Good Cell Cnt: 47797
Idle Cell Cnt: 1139617


[Downstream/RX)]
Good Cell Cnt: 300842
Idle Cell Cnt: 4607128
Bad Hec Cell Cnt: 0
Overflow Dropped Cell Cnt: 0

[SAR AAL5 Stats]
Tx PDU's: 12063
Rx PDU's: 14087
Tx Total Bytes: 2011176
Rx Total Bytes: 14230541
Tx Total Error Counts: 0
Rx Total Error Counts: 0


[OAM Stats]
Near End F5 Loop Back Count: 0
Near End F4 Loop Back Count: 0
Far End F5 Loop Back Count: 0
Far End F4 Loop Back Count: 0
SAR OAM Ping Response Drop Count=15

Modem DSL link information
SHOWTIME
1
failTrains=2

Trained modulation:
ADSL_G.dmt

Path mode:
Interleaved

Network statistics
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State
tcp 0 0 0.0.0.0:2048 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:www 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:domain 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ftp 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:telnet 0.0.0.0:* LISTEN
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4318 TIME_WAIT
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4316 TIME_WAIT
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4320 TIME_WAIT
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4326 TIME_WAIT
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4324 TIME_WAIT
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:4328 ESTABLISHED
udp 0 0 0.0.0.0:1812 0.0.0.0:*
udp 0 0 0.0.0.0:domain 0.0.0.0:*
udp 0 0 0.0.0.0:bootps 0.0.0.0:*
udp 0 0 0.0.0.0:tftp 0.0.0.0:*
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags Type State I-Node Path
unix 2 [ ] DGRAM 558 /var/tmp/cm_miniHttpd.ctl
unix 2 [ ] DGRAM 568 /var/tmp/cm_pc.ctl
unix 2 [ ] DGRAM 582 /var/tmp/cm_logic.ctl
unix 5 [ ] DGRAM 595 /dev/log
unix 2 [ ] DGRAM 597 /dev/klog
unix 2 [ ] DGRAM 3400
unix 2 [ ] DGRAM 1485
unix 2 [ ] DGRAM 1027
unix 2 [ ] STREAM 554
unix 2 [ ] DGRAM 553
unix 2 [ ] DGRAM 25

Iptables chains
Chain PREROUTING (policy ACCEPT 1468 packets, 113K bytes)
pkts bytes target prot opt in out source destination

Chain POSTROUTING (policy ACCEPT 9 packets, 573 bytes)
pkts bytes target prot opt in out source destination
133 8277 MASQUERADE all -- * ppp0 0.0.0.0/0 0.0.0.0/0

Chain OUTPUT (policy ACCEPT 435 packets, 27898 bytes)
pkts bytes target prot opt in out source destination

Chain INPUT (policy ACCEPT 761 packets, 57416 bytes)
pkts bytes target prot opt in out source destination
137 9392 CFG tcp -- any any 192.168.1.2 anywhere tcp dpt:www Records Packet's Source Interface

154 19581 ACCEPT all -- ppp0 any anywhere anywhere state RELATED,ESTABLISHED
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
0 0 DROP icmp -f any any anywhere anywhere
6 300 DROP all -- ppp0 any anywhere anywhere

Chain FORWARD (policy ACCEPT 11539 packets, 1594K bytes)
pkts bytes target prot opt in out source destination
75 4500 TCPMSS tcp -- any ppp0 anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU
3066 2945K ACCEPT all -- ppp0 any anywhere anywhere state RELATED,ESTABLISHED
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
0 0 DROP all -- ppp0 any anywhere anywhere

Chain OUTPUT (policy ACCEPT 1264 packets, 306K bytes)
pkts bytes target prot opt in out source destination
36 20736 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
19 3237 DROP icmp -- any ppp0 anywhere anywhere icmp destination-unreachable
0 0 DROP icmp -- any ppp0 anywhere anywhere state INVALID

Network interface details
br0 Link encap:Ethernet HWaddr 00:E0:FC:32:98:C4
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12664 errors:0 dropped:0 overruns:0 frame:0
TX packets:13881 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1918605 (1.8 MiB) TX bytes:14155669 (13.4 MiB)

br1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

br2 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0 Link encap:Ethernet HWaddr 00:E0:FC:32:98:C4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:479 dropped:479 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

nas0 Link encap:Ethernet HWaddr 00:00:02:03:04:05
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14190 errors:0 dropped:0 overruns:0 frame:0
TX packets:12232 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:13904397 (13.2 MiB) TX bytes:2026671 (1.9 MiB)

ppp0 Link encap:Point-to-Point Protocol
inet addr:117.193.117.162 P-t-P:117.193.112.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1
RX packets:3232 errors:0 dropped:0 overruns:0 frame:0
TX packets:2443 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2965684 (2.8 MiB) TX bytes:375998 (367.1 KiB)

wlan0 Link encap:Ethernet HWaddr 00:50:F1:12:12:10
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12664 errors:0 dropped:0 overruns:0 frame:0
TX packets:13881 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:1748015 (1.6 MiB) TX bytes:14155669 (13.4 MiB)


System Log
May 2 01:18:14 | Error getting mac from BootLoader enviroment for wlan0
May 2 01:18:14 | Using default mac address: 00.50.F1.12.12.10
May 2 01:18:14 | Use BootLoader command:
May 2 01:18:14 | setenv mac_ap xx.xx.xx.xx.xx.xx
May 2 01:18:14 | to set mac address
May 2 01:18:15 | Valid Configuration Tree
May 2 01:18:15 | NTP Polling Timer for DHCP Started succesfully.
May 2 01:18:15 | DSL Polling Timer Started succesfully.
May 2 01:18:15 | PSP Boot environment Modem Modulation Change: 0x1
May 2 01:18:15 | Firewall NAT service started
May 2 01:18:16 | Bridge Created: br0
May 2 01:18:18 | Bridge VLAN0 add eth0
May 2 01:18:18 | Bridge VLAN AUTO OFF.
May 2 01:18:18 | Bridge VLAN0 add eth1
May 2 01:18:18 | Bridge VLAN AUTO OFF.
May 2 01:18:18 | Bridge VLAN0 add eth2
May 2 01:18:18 | Bridge VLAN AUTO OFF.
May 2 01:18:18 | Bridge VLAN0 add eth3
May 2 01:18:18 | Bridge VLAN AUTO OFF.
May 2 01:18:18 | Bridge Created: br1
May 2 01:18:20 | WPA Authenticator Started
May 2 01:18:20 | Bridge Created: br2
May 2 01:18:23 | Bridge Interface Added: eth0
May 2 01:18:25 | Add Bridge Iface Error: 1
May 2 01:18:25 | Add Bridge Iface Error: 1
May 2 01:18:25 | USB is disabled
May 2 01:18:25 | DSL Carrier is down
May 2 01:18:26 | Add Bridge Iface Error: 1
May 2 01:18:28 | AP Driver configuration successful
May 2 01:18:33 | AP IS UP
May 2 01:18:33 | Bridge Interface Added: wlan0
May 2 01:18:55 | DSL Carrier is up
May 2 01:18:55 | sar read trained mode (1)(ADSL_G.dmt)
May 2 01:18:57 | ---}}} Start of connection delayed for 7 sec
May 2 01:19:04 | PPPoE Launch after conn delay timeout ...
May 2 01:19:05 | pppd 2.4.4 started by root, uid 0
May 2 01:19:07 | Got connection: 3b22
May 2 01:19:07 | New PPP_ID: 0x3b22
May 2 01:19:07 | Saved Session ID: 0
May 2 01:19:07 | AC MAC address: 00-30-88-23-07-db
May 2 01:19:07 | Connect: ppp0 {--} nas0
May 2 01:19:07 | CHAP authentication succeeded
May 2 01:19:07 | local IP address 117.193.98.233
May 2 01:19:07 | remote IP address 117.193.96.1
May 2 01:19:07 | PPPoE Connect with IP Address 117.193.98.233
May 2 01:19:08 | PPPoE Connection Successfully Established
May 2 01:19:08 | Renew PPPoE Session ID: 0x3b22
May 2 01:19:08 | PPPoE Connect with Gateway IP Address: 117.193.96.1
May 2 02:19:30 | onconnectWAN: Crond is already running.
Dec 16 09:55:26 | time disparity of 328835 minutes detected
Dec 16 09:58:23 | PPPoE Exit Status = 16
Dec 16 09:58:23 | Terminated: Modem Hang-Up
Dec 16 09:58:23 | Connection terminated.
Dec 16 09:58:23 | Doing disconnect
Dec 16 09:58:23 | Modem hangup
Dec 16 09:58:24 | pppd 2.4.4 started by root, uid 0
Dec 16 09:58:24 | Got connection: b814
Dec 16 09:58:24 | New PPP_ID: 0xb814
Dec 16 09:58:24 | Saved Session ID: 0
Dec 16 09:58:24 | AC MAC address: 00-30-88-23-07-db
Dec 16 09:58:24 | Connect: ppp0 {--} nas0
Dec 16 09:58:24 | CHAP authentication succeeded
Dec 16 09:58:25 | local IP address 117.193.105.128
Dec 16 09:58:25 | remote IP address 117.193.96.1
Dec 16 09:58:25 | PPPoE Connect with IP Address 117.193.105.128
Dec 16 09:58:25 | PPPoE Connection Successfully Established
Dec 16 09:58:25 | Renew PPPoE Session ID: 0xb814
Dec 16 09:58:25 | PPPoE Connect with Gateway IP Address: 117.193.96.1
Dec 16 09:58:47 | onconnectWAN: Crond is already running.
Dec 16 10:00:02 | DS Line Attenuation: 13 DS Margin: 31
Dec 16 10:00:02 | US Line Attenuation: 8 US Margin: 29
Dec 16 10:00:58 | Modem hangup
Dec 16 10:00:58 | Connection terminated.
Dec 16 10:00:58 | Doing disconnect
Dec 16 10:00:58 | PPPoE Exit Status = 16
Dec 16 10:00:58 | Terminated: Modem Hang-Up
Dec 16 10:01:02 | pppd 2.4.4 started by root, uid 0
Dec 16 10:01:03 | Got connection: 8c07
Dec 16 10:01:03 | New PPP_ID: 0x8c07
Dec 16 10:01:03 | Saved Session ID: 0
Dec 16 10:01:03 | PPPoE Connect with IP Address 117.193.98.229
Dec 16 10:01:03 | PPPoE Connection Successfully Established
Dec 16 10:01:03 | Renew PPPoE Session ID: 0x8c07
Dec 16 10:01:03 | PPPoE Connect with Gateway IP Address: 117.193.96.1
Dec 16 10:01:04 | AC MAC address: 00-30-88-23-07-db
Dec 16 10:01:04 | Connect: ppp0 {--} nas0
Dec 16 10:01:04 | CHAP authentication succeeded
Dec 16 10:01:04 | local IP address 117.193.98.229
Dec 16 10:01:04 | remote IP address 117.193.96.1
Dec 16 10:01:25 | onconnectWAN: Crond is already running.
Dec 16 10:08:06 | Modem hangup
Dec 16 10:08:06 | Connection terminated.
Dec 16 10:08:06 | Doing disconnect
Dec 16 10:08:06 | PPPoE Exit Status = 16
Dec 16 10:08:06 | Terminated: Modem Hang-Up
Dec 16 10:08:09 | pppd 2.4.4 started by root, uid 0
Dec 16 10:08:09 | Got connection: 3415
Dec 16 10:08:10 | New PPP_ID: 0x3415
Dec 16 10:08:10 | Saved Session ID: 0
Dec 16 10:08:10 | AC MAC address: 00-30-88-23-07-db
Dec 16 10:08:10 | Connect: ppp0 {--} nas0
Dec 16 10:08:10 | CHAP authentication succeeded
Dec 16 10:08:10 | local IP address 117.193.117.162
Dec 16 10:08:10 | remote IP address 117.193.112.1
Dec 16 10:08:10 | PPPoE Connect with IP Address 117.193.117.162
Dec 16 10:08:10 | PPPoE Connection Successfully Established
Dec 16 10:08:10 | Renew PPPoE Session ID: 0x3415
Dec 16 10:08:10 | PPPoE Connect with Gateway IP Address: 117.193.112.1
Dec 16 10:08:33 | onconnectWAN: Crond is already running.

Miscellaneous information
RouterTech firmware release: 2.96
Connecting from: 192.168.1.1 [192.168.1.2]
Router's internal name: mygateway1.AR7WRD
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #1 Mon May 2 01:14:30 BST 2011
BUILD=RouterTech_3.6.0D_20110502_2.96
VERSION=3.6.0D-RouterTech-Adam2
BOARD=AR7WRD
TARGET=Adam2_1-Port
FSSTAMP=20110502011811
ROHS=0
Core logic version: 3.6.0D
Boot Loader: Adam2 v0.22.02
ATM Driver version:[7.05.01.00]
DSL HAL version: [7.05.01.00]
DSP Datapump version: [7.05.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]
Ethernet ports: 1
Upstream rate (kbps): 480
Downstream rate (kbps): 1984
Trained Modulation: ADSL_G.dmt
Path Mode: Interleaved
System uptime: 0hr 19min - 0 day(s), 0 hour(s), 19 minute(s), and 5 second(s) (system 92% idle)
Bandwidth usage:
Downloads : 13.5855 MB
Uploads : 1.9285 MB
Line attenuation:
DS Line Attenuation: 13 DS Margin: 31
US Line Attenuation: 8 US Margin: 29
Memory usage:
In active use : 75% of 14180 kb
Available : 25% (3668 kb) of 14180 kb (of which 2820 kb is marked as "Inactive" and 848 kb is free)
Environment fragmentation:
Fragmentation level is "20" (out of 72 records). The threshold is "30".
Connection information:
WAN Uptime: 0hr 3min 15sec
WAN IP Address: 117.193.117.162
Connection Check #1 : 1 connection(s)
Connection Check #2 : 1 connection(s)
connection1

what may be the problem.. as only the status led is not functioning properly, other leds function properly

[thechief]

There may be any number of reasons. Those custom led conf files are not necessarily going to produce the best result in every case, and may just have to live with the problem.

PS: you can try this command at a telnet/ssh login session

Code: Select all

Led status 1

[harimkb]

thanks chief ,

i found out that the gpio for status Led is 8 from original huawei wa1003a led file
and ran the test script from viewtopic.php?f=3&t=3505 with gpio value as 8.. the led is glowing for various test parameters...

also , i am posting the original code for status led from wa1003a original firmware:

module = status # module = {adsl,usb,pppoe, status}
state = 0 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 500 # flash on duration in ms
param2 = 500 # flash off duration in ms

can you find any problems here...

Thanks

[anutham]

Chief,
I've got a problem with my wa1003a for almost 2 years.
The WiFi fails to switch on at times. I've still got firmware: V200R002C01B020
Dyu think upgrading da firmware can help?

[thechief]

Run the RUC.

[bhaskar]

I have updated my firmwire but feel it takes too long to connect to internet so I decided to go back to my old/original firmwire. I follow the following guide for the entire process, and from there the restoration process is:

Restoration Process:

1.goto command mode,

2. change directory to the folder that has mtd3 and mtd4 , in my case i have those files in C:\router....


cd C:\router

3.Now , Switch off the router

In command prompt and type ftp 192.168.1.199 and keep it ready (don’t press enter yet)

· Switch on the router and exactly after 2 to 3 seconds , press enter


once loggged in to ftp service ...
NOTE : USER NAME AND PASSWORD ARE BOTH "adam2"

enter following commands sequentially.

quote SETENV mtd0,0x90091000,0x903f0000
quote SETENV mtd1,0x90010090,0x90091000
quote SETENV mtd2,0x90000000,0x90010000
quote SETENV mtd3,0x903f0000,0x90400000
quote SETENV mtd4,0x90010000,0x903f0000

quote GETENV mtd0
quote GETENV mtd1
quote GETENV mtd2
quote GETENV mtd3
quote GETENV mtd4

quote "MEDIA FLSH"
bin

put mtd4 "fs mtd4"
put mtd3 "fs mtd3"

quote REBOOT

But after I entered

put mtd4 "fs mtd4"

ftp mode exits and now my modem is totally unusable. So, can anybody guide me to how to restore back my router in working condition.

P.S. Guide I followed http://pcideas.blogspot.in/2011/12/hack ... de-to.html

[thechief]

Get back into ftp mode and continue from where you left off - or try using the PCTool.

[bhaskar]

Get back into ftp mode and continue from where you left off - or try using the PCTool.

Thanks for your reply, but the ftp mode not starting up, showing error msg, that could not connect due to some unknown reason, also have tried PCTool, but it also not recognizing the device.

[thechief]

Well, there is nothing that you have typed that could have killed the bootloader, so, the bootloader is probably still intact. If it is intact, then the router is recoverable. You just have to figure out how to connect to it. It is possible that the environment has been trashed, which will return the environment variables to a small group of default entries. You might need to connect to some default IP address. Connect the router to your PC, and run "ipconfig /all". This will show you which IP address Windows has assigned (you need to turn on DHCP before this).

[bhaskar]

Well, there is nothing that you have typed that could have killed the bootloader, so, the bootloader is probably still intact. If it is intact, then the router is recoverable. You just have to figure out how to connect to it. It is possible that the environment has been trashed, which will return the environment variables to a small group of default entries. You might need to connect to some default IP address. Connect the router to your PC, and run "ipconfig /all". This will show you which IP address Windows has assigned (you need to turn on DHCP before this).

I am attaching the "ipconfig /all" screenshot in dhcp mode for you, the router hasnot assigned any ip address to my PC. This router has a USB interface too, shall I try to connect it via USB? will it help? if so then I need some time as I have lost the USB cable, so get a cable from market and then can update again.

[thechief]

The "Media disconnected" message is not encouraging. It is possible that the router's ethernet port is dead. If it is, then you're out of luck. If the router was not in a bricked state, a USB connection might have been possible - but, I think the router is already in a bricked state. There is no harm trying the USB connection, but I would be surprised it it worked. Be prepared to throw the router away ...

[bhaskar]

The "Media disconnected" message is not encouraging. It is possible that the router's ethernet port is dead. If it is, then you're out of luck. If the router was not in a bricked state, a USB connection might have been possible - but, I think the router is already in a bricked state. There is no harm trying the USB connection, but I would be surprised it it worked. Be prepared to throw the router away ...

Yes the usb port too not responding. So, I already have a backup router, so using it and the bricked one I dumped finally..

[thechief]

Unfortunately, electrical appliances die eventually ...

[default19in]

HELLO I ALSO TRIED ON MY QUIDWAY HUAWEI WA1003A ROUTER .AS Newbie SAID IT STUCK AT 31% & FAILED. NOW THE THING IS I DONT HAVE PROPER BACKUP AS PER STATED ABOVE SO IF Newbie OR ANYONE WHO TRIED THIS PROCESS SUCSSEFUL MIGHT HAVE PROPER BACKUP ,HE CAN ATTACHED HERE SO IT'LL HELP PEOPLE LIKE ME TO ATLEAST GET BACK TO ORIGINAL FIRMWARE BACK.
IF POSSIBLE PROCEDURE TO GET BACK TO ORIGINAL WITH SCREENSHOT WOULD BE BETTER.
WAITING FOR POSITIVE FEEDBACK. NEED HELP DESPERATLY .THANKS IN ADVANCED.