d-link dsl 500T trouble
d-link dsl 500T trouble
Hi.
I have updated the firmware to routertech 2.95 and router itself works fine. But I have some troubles with configuration.
Here is my problem:
I have done everything that was in the docs/upgrade.html, but my router just refuses to connect.. I've selected correct modulation type, created a new connection with my ISP settings (tried PPPoE and PPPoA, despite the fact that my ISP uses only PPPoE ), played with MRU and other settings and after I click on the Apply - Connect button (or Save All - Reboot) there is still no connection..
Here some screenshots (config itself, dsl statisticts, connection status and status on the home page)
Dsl stats shows that there is traffic between me and ISP, but connection status and statistics on the home page are saying that the WAN connection is down and Ping test in the tools section saying that the destination network is unreachable (8.8.8.8 )
Here is PC configuration:
IPv4-address. . . . . . . . . . . . : 192.168.1
Subnet mask . . . . . . . . . . : 255.255.255.0
Default Gateway. . . . . . . . . : 192.168.1.1 (router ip address)
Now I've configured router to work in the bridge mode and all works fine, but it would be better if the router will operate in "Router" mode..
What am I doing wrong? Thanks in advance.
I have updated the firmware to routertech 2.95 and router itself works fine. But I have some troubles with configuration.
Here is my problem:
I have done everything that was in the docs/upgrade.html, but my router just refuses to connect.. I've selected correct modulation type, created a new connection with my ISP settings (tried PPPoE and PPPoA, despite the fact that my ISP uses only PPPoE ), played with MRU and other settings and after I click on the Apply - Connect button (or Save All - Reboot) there is still no connection..
Here some screenshots (config itself, dsl statisticts, connection status and status on the home page)
Dsl stats shows that there is traffic between me and ISP, but connection status and statistics on the home page are saying that the WAN connection is down and Ping test in the tools section saying that the destination network is unreachable (8.8.8.8 )
Here is PC configuration:
IPv4-address. . . . . . . . . . . . : 192.168.1
Subnet mask . . . . . . . . . . : 255.255.255.0
Default Gateway. . . . . . . . . : 192.168.1.1 (router ip address)
Now I've configured router to work in the bridge mode and all works fine, but it would be better if the router will operate in "Router" mode..
What am I doing wrong? Thanks in advance.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
Post the system diagnostics.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: d-link dsl 500T trouble
Code: Select all
ROUTERTECH SYSTEM DIAGNOSTICS
Operating system version
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #1 Mon Jan 3 01:00:00 GMT 2011
Firmware version information
BUILD=RouterTech_3.6.0D_20110103_2.95
VERSION=3.6.0D-RouterTech-1P-Adam2
BOARD=AR7RD
TARGET=Adam2-4mb-flash
FSSTAMP=20110103010342
ROHS=0
PSP version information
Linux OS DSL-PSPOhioL version 4.5.0.5 Best and Final on BasePSP Version 5.7.6.12 Jan 3 2011 01:01:01
Avalanche SOC Version: 0x20005 operating in cached, write back, write allocate mode
Cpu Frequency:150 MHZ
System Bus frequency: 125 MHZ
Driver version information
Core Logic version: 3.6.0D
Texas Instruments CPMAC driver version: 1.5
Texas Instruments CPMAC HAL version: CPMAC 01.07.08 Jan 3 2011 01:00:11
ATM Driver version:[7.00.01.00]
DSL HAL version: [7.00.01.00]
DSP Datapump version: [7.00.04.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]
Modem Modulation Information
NO_MODE 0x0
ADSL_G.dmt 0x3
ADSL_G.lite 0x4
ADSL_G.dmt.bis 0x8
ADSL_G.dmt.bis_DELT 0x9
ADSL_2plus 0x10
ADSL_2plus_DELT 0x11
ADSL_re-adsl 0x20
ADSL_re-adsl_DELT 0x21
ADSL_ANSI_T1.413 0x2
MULTI_MODE 0x1
ADSL_G.dmt.bis_AnxI 0x0
ADSL_G.dmt.bis_AnxJ 0x0
ADSL_G.dmt.bis_AnxM 0x400
ADSL_2plus_AnxI 0x0
ADSL_2plus_AnxJ 0x0
ADSL_2plus_AnxM 0x2000
G.shdsl 0x0
IDSL 0x0
HDSL 0x0
SDSL 0x0
VDSL 0x0
System environment (/proc/sys/dev/adam2/environment)
Adam2_Release 0.22.02_b03_Mar 10 2005
autoload 1
autoload_timeout 7
bootloaderVersion 0.22.02
bootserport tty0
checksync.sh 1 20
connection0 0
cpufrequency 150000000
cron_enable 1
dsp_ver dsp70A
enable_margin_retrain 1
eoc_vendor_id 0x444C696E6B000000
eoc_vendor_revision 20071212
eoc_vendor_serialnum 00:17:9A:7E:E5:61_00000000000000
firstfreeaddress 0x9401d888
flashsize 0x00400000
HWA_HRNDIS 00:E0:A6:66:41:E1
HWA_RNDIS 00:E0:A6:66:41:EB
HWRevision Unknown
invntry_vernum 2007121200000000
led_conf led.500t
maca 00:17:9A:7E:E5:61
memchk.sh 1
memsize 0x01000000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
modulation 0x2000
mtd0 0x9008d000,0x903f0000
mtd1 0x90010090,0x9008d000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
my_ipaddress 192.168.1.1
ProductID AR7RD
prompt Adam2_AR7RD
req_fullrate_freq 125000000
SerialNumber 00:17:9A:7E:E5:61
StaticBuffer 120
SW_FEATURES 0X4000
sysfrequency 125000000
usb_man D-Link
usb_pid 0x5b00
usb_prod DSL-500T
usb_serial 1234567890
usb_vid 0x2001
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
CPU information
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 149.91
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
Memory (RAM) information
total: used: free: shared: buffers: cached:
Mem: 14553088 10334208 4218880 0 1347584 4259840
Swap: 0 0 0
MemTotal: 14212 kB
MemFree: 4120 kB
MemShared: 0 kB
Buffers: 1316 kB
Cached: 4160 kB
SwapCached: 0 kB
Active: 1732 kB
Inactive: 5348 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 14212 kB
LowFree: 4120 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Flash memory (chip) information
Flash type: AMD; Manufacturer=SAMSUNG.
Manufacturer_ID=0x00EC; Chip_ID=0x00A2; Chip_Size=0x400000; Erase_Regions=0x0002
Mount points
/dev/mtdblock/0 / squashfs ro 0 0
none /dev devfs rw 0 0
proc /proc proc rw 0 0
ramfs /var ramfs rw 0 0
Filesystems
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev shm
nodev pipefs
nodev ramfs
minix
nodev devfs
squashfs
MTD
dev: size erasesize name
mtd0: 00363000 00010000 "mtd0"
mtd1: 0007cf70 00010000 "mtd1"
mtd2: 00010000 00002000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 003e0000 00010000 "mtd4"
Kernel modules
tiatm 134216 1
Interrupts
7: 9453 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 191 serial [hw0 (Avalanche Primary)]
23: 26 + SAR [hw0 (Avalanche Primary)]
27: 491 + Cpmac Driver [hw0 (Avalanche Primary)]
47: 60 + DSL [hw0 (Avalanche Primary)]
Devices
Character devices:
1 mem
2 pty/m%d
3 pty/s%d
4 tts/%d
5 cua/%d
10 misc
108 ppp
128 ptm
136 pts/%d
162 raw
Block devices:
7 loop
31 mtdblock
Processes
PID USER VSZ STAT COMMAND
1 root 1052 S init
2 root 0 SW [keventd]
3 root 0 SWN [ksoftirqd_CPU0]
4 root 0 SW [kswapd]
5 root 0 SW [bdflush]
6 root 0 SW [kupdated]
7 root 0 SW [mtdblockd]
480 root 2300 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
481 root 2120 S /usr/bin/cm_pc
483 root 3628 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
502 root 744 S /sbin/dproxy -c /etc/resolv.conf -d
563 root 1052 S init
648 root 684 S /usr/sbin/udhcpd /var/tmp/udhcpd.conf
781 root 1060 S crond -b
853 root 2396 S /usr/sbin/pppd plugin pppoe wbif0 user user@dsl.ukr
896 root 1064 S N /bin/sh diagnostics.cgi
897 root 2344 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
902 root 632 S N /usr/local/bin/diagnostics
903 root 1056 S N sh -c /usr/local/bin/diagnostics.sh
904 root 1116 S N /bin/sh /usr/local/bin/diagnostics.sh
941 root 1052 R N /bin/ps
ADSL Modem information
AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
US Connection Rate: 2408 DS Connection Rate: 17482
DS Line Attenuation: 9 DS Margin: 10
US Line Attenuation: 3 US Margin: 11
US Payload : 1056 DS Payload: 768
US Superframe Cnt : 2021 DS Superframe Cnt: 2021
US Transmit Power : 9 DS Transmit Power: 16
LOS errors: 0 SEF errors: 0
Errored Seconds: 0 Severely Err Secs: 0
Frame mode: 0 Max Frame mode: 0
Trained Path: 1 US Peak Cell Rate: 5679
Trained Mode: 8192 Selected Mode: 8192
ATUC Vendor Code: 4753504E ATUC Revision: 3
Hybrid Selected: 1 Trellis: 1
Showtime Count: 1 DS Max Attainable Bit Rate: 17940 kbps
BitSwap: 1 US Max Attainable Bit Rate: 2616000 bps
Annex: AnxM psd_mask_qualifier: 0x001c
ATUC ghsVid: ff b5 47 53 50 4e 02 0b
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
ATUR ghsVid: 00 44 4c 69 6e 6b 00 00
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
[Upstream (TX) Interleave path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Downstream (RX) Interleave path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Upstream (TX) Fast path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Downstream (RX) Fast path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[ATM Stats]
[Upstream/TX]
Good Cell Cnt: 22
Idle Cell Cnt: 195130
Tx Packets Dropped Count: 0
Tx Bad Packets Count: 0
[Downstream/RX)]
Good Cell Cnt: 16
Idle Cell Cnt: 1416303
Bad Hec Cell Cnt: 0
Overflow Dropped Cell Cnt: 0
Rx Packets Dropped Count: 0
Rx Bad Packets Count: 0
[SAR AAL5 Stats]
Tx PDU's: 4
Rx PDU's: 8
Tx Total Bytes: 168
Rx Total Bytes: 592
Tx Total Error Counts: 0
Rx Total Error Counts: 0
[OAM Stats]
Near End F5 Loop Back Count: 0
Near End F4 Loop Back Count: 0
Far End F5 Loop Back Count: 0
Far End F4 Loop Back Count: 0
SAR OAM Ping Response Drop Count=15
Trained modulation:
ADSL_2plus_AnxM
Path mode:
Interleaved
Network statistics
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State
tcp 0 0 0.0.0.0:www 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:domain 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ftp 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:telnet 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:1050 0.0.0.0:* LISTEN
tcp 0 0 192.168.1.1:www 192.168.1.2:52211 TIME_WAIT
tcp 0 576 192.168.1.1:www 192.168.1.2:52213 ESTABLISHED
tcp 0 0 192.168.1.1:www 192.168.1.2:52200 TIME_WAIT
tcp 0 0 192.168.1.1:www 192.168.1.2:52202 TIME_WAIT
tcp 0 0 192.168.1.1:www 192.168.1.2:52206 TIME_WAIT
udp 0 0 0.0.0.0:domain 0.0.0.0:*
udp 0 0 0.0.0.0:bootps 0.0.0.0:*
udp 0 0 0.0.0.0:tftp 0.0.0.0:*
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags Type State I-Node Path
unix 2 [ ] DGRAM 557 /var/tmp/cm_miniHttpd.ctl
unix 2 [ ] DGRAM 567 /var/tmp/cm_pc.ctl
unix 2 [ ] DGRAM 581 /var/tmp/cm_logic.ctl
unix 5 [ ] DGRAM 594 /dev/log
unix 2 [ ] DGRAM 596 /dev/klog
unix 2 [ ] DGRAM 1334
unix 2 [ ] DGRAM 1162
unix 2 [ ] DGRAM 1023
unix 2 [ ] STREAM 553
unix 2 [ ] DGRAM 552
unix 2 [ ] DGRAM 25
Iptables chains
Chain PREROUTING (policy ACCEPT 140 packets, 8388 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain INPUT (policy ACCEPT 146 packets, 14228 bytes)
pkts bytes target prot opt in out source destination
117 9662 CFG tcp -- any any 192.168.1.2 anywhere tcp dpt:www Records Packet's Source Interface
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
0 0 DROP icmp -f any any anywhere anywhere
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
Chain OUTPUT (policy ACCEPT 269 packets, 134K bytes)
pkts bytes target prot opt in out source destination
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
Network interface details
br0 Link encap:Ethernet HWaddr 00:17:9A:7E:E5:61
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:262 errors:0 dropped:0 overruns:0 frame:0
TX packets:275 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:20966 (20.4 KiB) TX bytes:139697 (136.4 KiB)
br1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br2 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:17:9A:7E:E5:61
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:288 errors:0 dropped:0 overruns:0 frame:0
TX packets:273 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:27121 (26.4 KiB) TX bytes:139613 (136.3 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
nas0 Link encap:Ethernet HWaddr 00:00:02:03:04:05
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:400 (400.0 B) TX bytes:168 (168.0 B)
wbif0 Link encap:Ethernet HWaddr 00:44:2B:02:55:44
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:288 (288.0 B) TX bytes:128 (128.0 B)
System Log
Jan 3 01:03:14 | Valid Configuration Tree
Jan 3 01:03:14 | NTP Polling Timer for DHCP Started succesfully.
Jan 3 01:03:14 | DSL Polling Timer Started succesfully.
Jan 3 01:03:14 | PSP Boot environment Modem Modulation Change: 0x2000
Jan 3 01:03:14 | Firewall NAT service started
Jan 3 01:03:15 | Bridge Created: br0
Jan 3 01:03:16 | Bridge VLAN0 add eth0
Jan 3 01:03:16 | Bridge VLAN AUTO OFF.
Jan 3 01:03:16 | Bridge Created: br1
Jan 3 01:03:18 | Bridge Created: br2
Jan 3 01:03:19 | Bridge Interface Added: eth0
Jan 3 01:03:21 | USB is disabled
Jan 3 01:03:24 | DSL Carrier is down
Jan 3 01:03:54 | DSL Carrier is up
Jan 3 01:03:54 | sar read trained mode (16)(ADSL_2plus_AnxM)
Jan 3 01:03:55 | ---}}} Start of connection delayed for 4 sec
Jan 3 01:03:59 | PPPoE Launch after conn delay timeout ...
Jan 3 01:04:00 | pppd 2.4.4 started by root, uid 0
Miscellaneous information
RouterTech firmware release: 2.95
Connecting from: 192.168.1.1 [192.168.1.2]
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #1 Mon Jan 3 01:00:00 GMT 2011
BUILD=RouterTech_3.6.0D_20110103_2.95
VERSION=3.6.0D-RouterTech-1P-Adam2
BOARD=AR7RD
TARGET=Adam2-4mb-flash
FSSTAMP=20110103010342
ROHS=0
Core logic version: 3.6.0D
Boot Loader: Adam2 v0.22.02
ATM Driver version:[7.00.01.00]
DSL HAL version: [7.00.01.00]
DSP Datapump version: [7.00.04.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]
Router's internal name: .
Ethernet ports: 1
Upstream rate (kbps): 2408
Downstream rate (kbps): 17482
Trained Modulation: ADSL_2plus_AnxM
Path Mode: Interleaved
System uptime: 0hr 1min - 0 day(s), 0 hour(s), 1 minute(s), and 52 second(s) (system 65% idle)
Bandwidth usage:
Downloads : 0.0934 MB
Uploads : 0.0003 MB
Line attenuation:
DS Line Attenuation: 9 DS Margin: 10
US Line Attenuation: 3 US Margin: 11
Memory usage:
In active use : 35% of 14212 kb
Available : 65% (9332 kb) of 14212 kb (of which 5488 kb is marked as "Inactive" and 3844 kb is free)
Environment fragmentation:
The environment does not seem to be fragmented.
Connection information:
There is no successful connection to the internet.
The existing (unsuccessful) connection(s):
connection0
Re: d-link dsl 500T trouble
There have been quite a few reports of PPPoE not working, and where the ISP supports PPPoA as well that usually works. Unfortunately we don't know why - is there anything special when you make the PPP endpoint on your PC, "service name", MTU, MRU, authentication type? D-Link pppd generally works in such cases, but we don't know what they have done to it, or the "core-logic" that configures it.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
Why are you using this modulation?Trained Modulation: ADSL_2plus_AnxM
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: d-link dsl 500T trouble
No, just created a "new high speed dsl connection" in windows 7..Unfortunately we don't know why - is there anything special when you make the PPP endpoint on your PC, "service name", MTU, MRU, authentication type?
I have used it on the previous (D-Link) firmware and my ISP told me to use it. Bridge connection works fine with that modulation.Why are you using this modulation?
I've already tried to use MULTI_MODE and ADSL_2plus modulation but there is still no connection.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
Post the RUC output from the Dlink firmware before you upgraded to RouterTech.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: d-link dsl 500T trouble
00:00:000 Running script
00:00:001 Opening connection
00:00:288 ÿýÿý!ÿûÿû
BusyBox on (none) login:
00:00:506 Password:
00:00:507 Delay for 3 second(s)
00:03:517 BusyBox v0.61.pre (2007.12.12-07:42+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
00:03:735 shell: No such file or directory
#
00:03:954 cm_cli_tty: No such file or directory
#
00:04:171 End of script
00:04:171 PID Uid VmSize Stat Command
1 root 1284 S init
2 root S [keventd]
3 root S [ksoftirqd_CPU0]
4 root S [kswapd]
5 root S [bdflush]
6 root S [kupdated]
7 root S [mtdblockd]
28 root 2776 S /usr/bin/cm_pc
29 root 1656 S /usr/sbin/diap
31 root 1284 S init
32 root 3756 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
69 root 640 S /sbin/dproxy -c /etc/resolv.conf -d
73 root 660 S /usr/sbin/ddnsd
355 root 2672 S /usr/sbin/pppd plugin pppoe nas0 linkname nas0 user
424 root 1252 S /usr/sbin/thttpd -g -d /var/tmp -u root -p 80
431 root 628 S /sbin/utelnetd
432 root 1288 S -sh
435 root 1284 R ps
#
00:04:173 Closed connection.
00:00:000 Running script
00:00:001 Opening connection
00:00:244 usyBox on (none) login:
00:00:463 Password:
00:00:682 BusyBox v0.61.pre (2007.12.12-07:42+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
00:00:900 memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
Adam2_Release 0.22.02_b03_Mar 10 2005
ProductID AR7RD
HWRevision Unknown
SerialNumber 00:e0:a0:a6:66:70
my_ipaddress 5.8.8.8
prompt Adam2_AR7RD
firstfreeaddress 0x9401d888
req_fullrate_freq 125000000
maca 00:17:9A:7E:E5:61
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
autoload 1
autoload_timeout 7
StaticBuffer 120
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_vid 0x0
usb_pid 0x0
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
modulation 0xffff
usb_man N/A
usb_prod N/A
usb_serial N/A
eoc_vendor_id 0x444C696E6B
enable_margin_retrain 1
eoc_vendor_serialnum 00:e0:a0:a6:66:70
eoc_vendor_revision 20060517
SW_FEATURES 0X4000
#
00:01:324 memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
Adam2_Release 0.22.02_b03_Mar 10 2005
ProductID AR7RD
HWRevision Unknown
SerialNumber 00:e0:a0:a6:66:70
my_ipaddress 5.8.8.8
prompt Adam2_AR7RD
firstfreeaddress 0x9401d888
req_fullrate_freq 125000000
maca 00:17:9A:7E:E5:61
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
autoload 1
autoload_timeout 7
StaticBuffer 120
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_vid 0x0
usb_pid 0x0
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
modulation 0xffff
usb_man N/A
usb_prod N/A
usb_serial N/A
eoc_vendor_id 0x444C696E6B
enable_margin_retrain 1
eoc_vendor_serialnum 00:e0:a0:a6:66:70
eoc_vendor_revision 20060517
SW_FEATURES 0X4000
#
00:01:539 #
00:01:561 #
00:01:774 #
00:01:991 End of script
00:01:991 PID Uid VmSize Stat Command
1 root 1284 S init
2 root S [keventd]
3 root S [ksoftirqd_CPU0]
4 root S [kswapd]
5 root S [bdflush]
6 root S [kupdated]
7 root S [mtdblockd]
28 root 2776 S /usr/bin/cm_pc
29 root 1656 S /usr/sbin/diap
31 root 1284 S init
32 root 3756 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
69 root 640 S /sbin/dproxy -c /etc/resolv.conf -d
73 root 660 S /usr/sbin/ddnsd
355 root 2672 S /usr/sbin/pppd plugin pppoe nas0 linkname nas0 user
436 root 628 S /sbin/utelnetd
437 root 1296 S -sh
443 root 1176 S /usr/sbin/thttpd -g -d /var/tmp -u root -p 80
444 root 1284 R ps
#
00:01:992 Closed connection.
MTD3 file downloaded & saved.
00:00:000 Running script
00:00:001 Opening connection
00:00:251 usyBox on (none) login:
00:00:454 Password:
00:00:672 BusyBox v0.61.pre (2007.12.12-07:42+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
00:00:890 #
00:01:094 #
00:01:312 #
00:01:530 End of script
00:01:530 PID Uid VmSize Stat Command
1 root 1284 S init
2 root S [keventd]
3 root S [ksoftirqd_CPU0]
4 root S [kswapd]
5 root S [bdflush]
6 root S [kupdated]
7 root S [mtdblockd]
28 root 2776 S /usr/bin/cm_pc
29 root 1656 S /usr/sbin/diap
31 root 1284 S init
32 root 3756 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
69 root 640 S /sbin/dproxy -c /etc/resolv.conf -d
73 root 660 S /usr/sbin/ddnsd
355 root 2672 S /usr/sbin/pppd plugin pppoe nas0 linkname nas0 user
445 root 628 S /sbin/utelnetd
446 root 1296 S -sh
450 root 1176 S /usr/sbin/thttpd -g -d /usr/www -u root -p 80 -c /cg
451 root 1284 R ps
#
00:01:531 Closed connection.
00:00:000 Running script
00:00:001 Opening connection
00:00:255 usyBox on (none) login:
00:00:473 Password:
00:00:692 BusyBox v0.61.pre (2007.12.12-07:42+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
00:00:693 Delay for 1 second(s)
00:01:704 #
00:01:924 Delay for 5 second(s)
00:06:930 /var
#
00:07:150 Delay for 1 second(s)
00:08:162 rm: cannot remove `/var/cm_cli_tty': No such file or directory
#
06:23:356 wget: Unable to connect to remote host (192.168.0.5): No route to host
#
06:23:356 Closed connection.
Aborted by user.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
This is problematic. Do a forum search for "0xffff" and you'll see why. My advice is that, if things continue to be problematic, to consider returning to your Dlink firmware, which obviously understands the need for a modulation value of 0xffff (which normally means nothing that I know of).modulation 0xffff
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
-
- Newbie
- Posts: 2
- Joined: Wed Mar 10, 2010 8:19 am
Re: d-link dsl 500T trouble
could u please try this step.
login to webgui, disconnect your connection first (Config Manager Stopped the PPPoE Session)
login to ssh, type the following commands :
# ifconfig nas0 down
# ifconfig nas0 hw ether 00:50:BA:xx:xx:xx
# ifconfig nas0 up
back to webgui, click connect and check the status. seems my isp didn't like -> 00:00:02:03:04:05 at all
login to webgui, disconnect your connection first (Config Manager Stopped the PPPoE Session)
login to ssh, type the following commands :
# ifconfig nas0 down
# ifconfig nas0 hw ether 00:50:BA:xx:xx:xx
# ifconfig nas0 up
back to webgui, click connect and check the status. seems my isp didn't like -> 00:00:02:03:04:05 at all
Re: d-link dsl 500T trouble
thanks, but that didn't help.. I have tried different combinations but results were the same..free2rhyme wrote:could u please try this step.
login to webgui, disconnect your connection first (Config Manager Stopped the PPPoE Session)
login to ssh, type the following commands :
# ifconfig nas0 down
# ifconfig nas0 hw ether 00:50:BA:xx:xx:xx
# ifconfig nas0 up
back to webgui, click connect and check the status. seems my isp didn't like -> 00:00:02:03:04:05 at all
In this document there is a note about 0xffff modulation. Can I do anything like that in the routertech firmware? Or can I take the pppd from d-link official firmware and use it in the routertech? Or can I connect my router to the "some user-friendly" linux desktop, and setup a bridge connection via GUI in there and use parameters of pppd (in the processlist) in my router's pppd? Windows works well in bridge mode with my router but I can't see any connection properties like mtu or something like that..This is problematic. Do a forum search for "0xffff" and you'll see why. My advice is that, if things continue to be problematic, to consider returning to your Dlink firmware, which obviously understands the need for a modulation value of 0xffff (which normally means nothing that I know of).
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
Don't know about "some user-friendly linux desktop" for setting up bridge connections. But the answer to your other questions is "no" - but you can run this from telnet
Code: Select all
setenv modulation 0xffff
/sbin/reboot
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: d-link dsl 500T trouble
Are you sure that you should be using an Annex A DSP driver? Clearly the RUC did not complete its task before you upgraded (which itself should have been warning enough), because there is no information about the DSP driver that you were running with your Dlink firmware.DSP Datapump version: [7.00.04.00] Annex A
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
-
- Newbie
- Posts: 2
- Joined: Wed Mar 10, 2010 8:19 am
Re: d-link dsl 500T trouble
sorry it didn't work for you.
to thechief,
i have 2 adsl connection with both using dlink 2540t. i installed routertech fw 2.95. as my suggestion step above, my modem only work in router mode if i set nas0 mac instead of using default addr 00:00:02:03:04:05. please kindly tell me how to set this permanently, either using a script or change it in a file.
thanks for your help.
to thechief,
i have 2 adsl connection with both using dlink 2540t. i installed routertech fw 2.95. as my suggestion step above, my modem only work in router mode if i set nas0 mac instead of using default addr 00:00:02:03:04:05. please kindly tell me how to set this permanently, either using a script or change it in a file.
thanks for your help.
Re: d-link dsl 500T trouble
I'm sorry about that, here is full report:Are you sure that you should be using an Annex A DSP driver? Clearly the RUC did not complete its task before you upgraded (which itself should have been warning enough), because there is no information about the DSP driver that you were running with your Dlink firmware.
Router Upgrade Check 1.4.1 06.03.2011 10:52:25
Router IP: 192.168.1.1
CLI is needed
Description: Dlink DSL-500T
Board type: AR7VW
Product ID: AR7RD
Bootloader: adam2
RAM 16,0 MB
Flash (ROM) 4,0 MB
ADAM2: Yes
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build:
Firmware version: V3.02B01T01.RU.20071212
Firmware stamp: 20071212154455
CPU: MIPS 4KEc V4.8
DSP: 7.03.01.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: No
TIAP: No
TNETW: No
Wireless: No
WIFI chip: N/A
WIFI chip conf: No
Ports: 1
Ports (according to router): N/A
Marvell (or Marvell like): No
NSP: V3.02B01T01.RU.20071212
Manufacturers: D-link Corporation
RNDIS: Telogy Networks Inc
HRNDIS: Telogy Networks Inc
Warning! Core Logic (NSP) could not be read. If the Core Logic version is too low you may need to upgrade to your router manufacturer's latest firmware first.
Select an AR7RD ADAM2 1 PORT firmware.
Latest: routertech-ar7rd-adam2-1port-firmware-20110103.zip
Please read the instructions that come with the firmware files before you upgrade.
Note: a later version of the firmware may exist depending on the how up to date the RUC is.
The date-stamp may be superseded, but the rest of the filename should be the same.
With your current MTD values, you have to upgrade your firmware using a single firmware image. Do NOT try to upgrade by using separate config + kernel + filesystem images.
/etc /versions
CUSTOMER=DLinkRU
MODEL=DSL-500T
VERSION=V3.02B01T01.RU.20071212
HTML_LANG=EN.302
BOARD=AR7VW
VERSION_ID=
CPUARCH_NAME=AR7
MODEL_ID=
FSSTAMP=20071212154455
#
/proc/wlan
cd: can't cd to /proc/wlan
#
/usr/sbin/wlan
cd: can't cd to /usr/sbin/wlan
#
/proc/ticfg/env
memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
Adam2_Release 0.22.02_b03_Mar 10 2005
ProductID AR7RD
HWRevision Unknown
SerialNumber 00:e0:a0:a6:66:70
my_ipaddress 192.168.1.1
prompt Adam2_AR7RD
firstfreeaddress 0x9401d888
req_fullrate_freq 125000000
maca 00:17:9A:7E:E5:61
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
autoload 1
autoload_timeout 7
StaticBuffer 120
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_vid 0x0
usb_pid 0x0
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
modulation 0xffff
usb_man N/A
usb_prod N/A
usb_serial N/A
eoc_vendor_id 0x444C696E6B
enable_margin_retrain 1
eoc_vendor_serialnum 00:e0:a0:a6:66:70
eoc_vendor_revision 20060517
SW_FEATURES 0X4000
#
/proc/sys/dev/adam2/environment
memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
Adam2_Release 0.22.02_b03_Mar 10 2005
ProductID AR7RD
HWRevision Unknown
SerialNumber 00:e0:a0:a6:66:70
my_ipaddress 192.168.1.1
prompt Adam2_AR7RD
firstfreeaddress 0x9401d888
req_fullrate_freq 125000000
maca 00:17:9A:7E:E5:61
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
mtd4 0x90010000,0x903f0000
autoload 1
autoload_timeout 7
StaticBuffer 120
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
usb_vid 0x0
usb_pid 0x0
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
modulation 0xffff
usb_man N/A
usb_prod N/A
usb_serial N/A
eoc_vendor_id 0x444C696E6B
enable_margin_retrain 1
eoc_vendor_serialnum 00:e0:a0:a6:66:70
eoc_vendor_revision 20060517
SW_FEATURES 0X4000
#
/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@james) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Wed Dec 12 15:39:32 CST 2007
#
/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 149.91
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
#
/proc/avalanche/avsar_ver
ATM Driver version:[7.03.01.00]
DSL HAL version: [7.03.01.00]
DSP Datapump version: [7.03.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [7300/7300A]
#
/proc/interrupts
7: 8245771 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 6858 serial [hw0 (Avalanche Primary)]
23: 5612211 + SAR [hw0 (Avalanche Primary)]
27: 1510599 + Cpmac Driver [hw0 (Avalanche Primary)]
47: 1578 + DSL [hw0 (Avalanche Primary)]
#
/proc/modules
tiatm 137864 1
#
/proc/flashinfo
cat: /proc/flashinfo: No such file or directory
#
/etc/PORTS
cat: /etc/PORTS: No such file or directory
#
logic:status/nspver
V3.02B01T01.RU.20071212
logic:status/has_marvell
0
/etc /led.conf
#################################################################
# Configuration File for AR7RD board
##################################################################
##################################################################
# The GPIO numbers 0 to 31 ==> correspond to GPIO pins #########
# The GPIO numbers 32,33 are mapped to ADSL (LED) pins ###########
##################################################################
module = adsl # module = {adsl,usb,pppoe}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 200 # flash on duration in ms
param2 = 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 25 # blink/flash rate in ms
######################################################################
module = usb # module = {adsl,usb,pppoe}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = cpmac # module = {adsl,usb,pppoe}
state = 0 # 0 = link down, 1 = link up, 6 = pkt rcv, 7 = pkt xmit
gpio = 7 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 6 = pkt rcv, 7 = pkt xmit
gpio = 7 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 6 # 0 = link down, 1 = link up, 6 = pkt rcv, 7 = pkt xmit
gpio = 7 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 7 # 0 = link down, 1 = link up, 6 = pkt rcv, 7 = pkt xmit
gpio = 7 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = status # module = {adsl,usb,pppoe, status}
state = 0 # 0 = status down, 1 = status active
gpio = 9 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = status down, 1 = status active
gpio = 9 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = status down, 1 = status active
gpio = 9 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 500 # flash on duration in ms
param2 = 500 # flash off duration in ms