RouterTech Firmware v2.8 Release (20081123)

Software and Firmware releases made by our in-house development team. You may not post here, but subscribing to this forum will allow you to be notified of all new releases, and this is recommended. Support for releases will be provided in the Software/Firmware forums.
Locked
User avatar
Kieran
RouterTech Team
RouterTech Team
Posts: 2675
Joined: Fri Jan 20, 2006 11:30 am
Location: London
Contact:

RouterTech Firmware v2.8 Release (20081123)

Post by Kieran » Sun Nov 23, 2008 2:40 pm

NOTE: this firmware has been superseded by a newer version. You can get the latest version HERE
RouterTech Firmware v2.8

Version: v2.8 (20081123)
Author: RouterTech Development Team (thechief)
Other contributor(s): mstombs
Testers: Various RT staff & forum members

Compatible Routers
A list of compatible routers is available in our knowledge base. Please check this before even contemplating an upgrade and remember you should always ask in our forum if unsure. Also see the section below on backing up and compatibility.

Disclaimer & Warning

1. Flashing custom firmwares onto a router is not for novices, as the process may well "brick" the router.

2. You must not flash this firmware onto your router unless you are very familiar with the PC-Tool (or similar) and are competent in using it to un-brick a router.

3. Please take this warning very seriously. If you are not adept at recovering bricked routers, and if you are not familiar with the PC-Tool, then do not install this firmware!

4. Do not even consider installing this firmware without first reading all the documentation supplied with the firmware. If you fail to observe this, then you are entirely on your own.

5. Do not even consider installing this firmware without first running the Router Upgrade Checker (RUC) and following whatever counsel it gives. If you fail to observe this, then you are entirely on your own.

6. Do not even consider installing this firmware unless you have first backed up your router's bootloader environment (i.e., /proc/ticfg/env) to your hard disk. If you fail to observe this, then you are entirely on your own.


Backing up & Compatibility
For ease we recommend you run the Router Upgrade Checker - this will backup your environment, LED config, current config, default config, generate a recovery script for the bootloader environment, and tell you if your router is suitable for this firmware.

Upgrading
Before upgrading you must backup your router config as detailed above and reset to factory defaults.

Please remember to run the Router Upgrade Check BEFORE you upgrade!

If you choose to upgrade via the router's web interface, then you MUST observe the following
  1. First reset the router to factory defaults before trying to install this firmware.
  2. When upgrading via the web interface, (particularly for the ROHS wireless firmware) you must wait for at least 7 minutes for the new firmware to establish itself. Do not do anything to the router for at least 7 minutes from the moment the upgrade process starts, and do not interrupt the upgrade process.
  3. Once your router has been upgraded and be seen to be working you must reset to factory defaults again
Note: Before installing this firmware, you must, among other things (see the docs in the zip file for those other things) back up a copy of your router's current "/etc /led.conf" file. We only have a few LED configuration files, and the chances are that we do not have one suitable for your own router. If you do not keep a copy of the original contents of that file, then we have no way of knowing how your LEDs should be configured, and the LEDs will always be wrong. This will not affect the router's normal operation - but you the LEDs will not be reporting the correct operations.

The Router Upgrade Checker as described in the backup and compatibility section above can backup your LED config - if you use the Router Upgrade Checker then you can double-check the output by looking in the check*.txt file for data after the "/etc /led.conf" line.

Comprehensive Documentation and Frequently Asked Questions (FAQs)
While full documentation is included with every release of our firmware we have also made it available as a separate download below so you can take time to read it before even needing to download a firmware. The router upgrade and firmware FAQs are also hosted online HERE. We recommend you do this as it will give you a chance to properly familiarise yourself with the process and get every angle covered etc.

PC-Tool and repairing / unbricking
Please see this forum topic

Files
Assuming your router is compatible, you just need to download the release that matches your router - if you have wireless and the Adam2 bootloader then you would download "Standard Wireless (Adam2 bootloader)".

Changelog
1. Fixes for pppoe connectivity issues with some ISPs.
2. New 4mb-flash firmware images for non-wireless Adam2 routers with 4mb flash.
3. Non-wireless firmwares have had their DSP drivers updated to 7.03.
4. Tinyproxy has been removed from firmwares for non-wireless routers with 2mb flash. The firmware images had become too big to fit in the mtd partitions.
5. This is the last firmware release for routers with 2mb flash.
6. Only single (combined) firmware images are now supplied. If your router requires separate images, then you have to convert your mtd partitions to use single image upgrades. The Router Repair Tool can assist you in this process.
7. New version of Busybox (1.12.2).
8. More support for QOS has been added to wireless firmwares and "4mb-flash" non-wireless firmwares. Hopefully QOS will work better now. This is still work-in-progress.

Downloading
The links to our firmware require you to be registered and logged into the site to see and use them. This is to make sure we can provide you with support easily (in this forum) if you need it. When logged in they appear below this post.

BE SURE TO READ ALL THE DOCUMENTATION IN THE FIRMWARE DOWNLOADS BEFORE TRYING ANYTHING WITH THIS FIRMWARE. Otherwise, YOU ARE ON YOUR OWN.

Sourcecode
As usual sourcecode, released under the GPL, is made available for budding developers. Download the packages from our fast dedicated source code server using the links below.
Standard
ROHS
Attachments
routertech_ar7wrd_pspboot_firmware_20081123.zip
Standard Wireless (pspboot bootloader). Suitable for the original SWAMR 54108/54125/SWART2-54125/GWART2-54125 series, and other 4-port PSPBOOT-based AR7WRD routers using the TNETW1130 wifi chip (DO NOT USE WITH ROUTERS USING THE TNETW1350A chip)
(3.31 MiB) Downloaded 884 times
routertech_ar7wrd_adam2_firmware_20081123.zip
Standard Wireless (Adam2 bootloader). Suitable for the original Solwise SAR600EW series, DLink G604T, and other 4-port ADAM2-based AR7WRD routers using the TNETW1130 wireless chip (DO NOT USE WITH ROUTERS USING THE TNETW1350A WIRELESS CHIP).
(3.31 MiB) Downloaded 1758 times
routertech_ar7wrd_1350a_pspboot_firmware_20081123.zip
Wireless (psp bootloader) with the TNETW1350A wifi chip. Suitable for the "R" series Solwise SAR 600EW, Solwise SAR605EW, PTI 8505G, newer SWART2-54125 series, and other compatibles. NOT suitable for the Asian dual antenna Aztech DSL605EW.
(6.55 MiB) Downloaded 531 times
routertech_ar7rd_pspboot_4ports_firmware_20081123.zip
4 Port Non-Wireless (pspboot bootloader). Suitable for the SART2-4115/GART2-4115, the new "R" series Solwise 600ER and 605ER, and other 4-port PSPBOOT-based AR7RD routers.
(6.63 MiB) Downloaded 424 times
routertech_ar7rd_pspboot_1port_firmware_20081123.zip
1 Port Non-Wireless (pspboot bootloader). Suitable for the SART2-4112/GART2-4112, the ADSL2MUE, the new "R" series Solwise 600E, and other 1-port PSPBOOT-based AR7RD routers.
(6.62 MiB) Downloaded 956 times
routertech_ar7rd_adam2_4ports_firmware_20081123.zip
4 Port Non-Wireless (Adam2 bootloader)
(6.63 MiB) Downloaded 606 times
routertech_ar7rd_adam2_1port_firmware_20081123.zip
1 Port Non-Wireless (Adam2 bootloader)
(6.62 MiB) Downloaded 488 times
routertech_firmware_20081123_docs.zip
Comprehensive documentation on upgrading etc.
(194.42 KiB) Downloaded 908 times
Kieran
"Indeed!"
Invaluable links: Forum Rules | Networking Guides | FAQ | Site Search | Forum Search <-- Use it or feel my wrath!
No support via PM, please ask your questions in the forum!
Locked