RouterTech Firmware 2.9 Discussion

Chris_TG · Post by **Chris_TG** » Sun Apr 19, 2009 9:28 pm

hadiceberg wrote:I can't connect to my ISP using RT v2.9 nor v2.8
Anyone managed to establish PPPoE on a D-Link DSL-2640T ?

Do you have Annex B?

Post by **thechief** » Sun Apr 19, 2009 9:37 pm

brylok1981 wrote:HI

can i update my config backup file to 2.9?

I don't understand what you mean. You should not restore a backup of a config from an earlier firmware. Of course, you can back up your reconfigured v2.9 config, and restore that later ...

der_Kief · Post by **der_Kief** » Sun Apr 19, 2009 9:38 pm

mstombs wrote:
der_Kief wrote:Hi,

does this new version support devices with 2MB flash ?
I didnt found a notice about that in actual release notes.
The only thing i found was a notice in the ver. 2.8 release note:

5. This is the last firmware release for routers with 2mb flash.

der_Kief
Yes you will find new 2MB flash versions, the support has been extended with the pppoe/ memory improvements that have been worked on.

...

Thats pretty cool. Thanks for the Info. Will try it as soon as possible on my Sphairon AR860.
Thanks for the hard work.

der_Kief

hadiceberg · Post by **hadiceberg** » Sun Apr 19, 2009 9:40 pm

Chris_TG wrote:
hadiceberg wrote:I can't connect to my ISP using RT v2.9 nor v2.8
Anyone managed to establish PPPoE on a D-Link DSL-2640T ?
Do you have Annex B?

My original firmware is Annex A and I also used RT2.9 annex A.

My current working Dlink firmware:

Code: Select all

ADSL Firmware Version:  	7.03.01.00 - 7.03.01.00 - 7.03.01.00 Annex A - 01.07.2c - 0.54
ADSL Software Version: 	V3.02B01T01.EU-A.20080725
Line State 	Connected
Modulation 	ADSL_2plus
Annex Mode 	Annex A
Max Tx Power 	-38 dBm/Hz

brylok1981 · Post by **brylok1981** » Sun Apr 19, 2009 10:19 pm

thechief wrote:
brylok1981 wrote:HI

can i update my config backup file to 2.9?
I don't understand what you mean. You should not restore a backup of a config from an earlier firmware. Of course, you can back up your reconfigured v2.9 config, and restore that later ...

i will tray again

can i convert config backup from older firmware to 2.9?

Post by **thechief** » Sun Apr 19, 2009 10:31 pm

brylok1981 wrote:can i convert config backup from older firmware to 2.9?

No.

notinthisworld · Post by **notinthisworld** » Mon Apr 20, 2009 12:19 am

thechief wrote:The Asian dual-antenna DSL605EW was not supported by v2.8 (because of "errata" in the flash chips in some batches, which were later fixed in subsequent batches). This should be okay now in v2.9, as we have found work-arounds for the errata. However, as usual, your mileage may vary. Be prepared for un-bricking, if it all goes pear shaped.

ahh i see, so which file should i download then? thanks again

Post by **Neo** » Mon Apr 20, 2009 2:14 am

thechief wrote:The Asian dual-antenna DSL605EW was not supported by v2.8 (because of "errata" in the flash chips in some batches, which were later fixed in subsequent batches). This should be okay now in v2.9, as we have found work-arounds for the errata. However, as usual, your mileage may vary. Be prepared for un-bricking, if it all goes pear shaped.

I have updated v1.3.4 of the RUC to reflect this.

notinthisworld, if you download 1.3.4 of the RUC again and run it, you should be told which firmware package to use

notinthisworld · Post by **notinthisworld** » Mon Apr 20, 2009 12:47 pm

Neo wrote:
thechief wrote:The Asian dual-antenna DSL605EW was not supported by v2.8 (because of "errata" in the flash chips in some batches, which were later fixed in subsequent batches). This should be okay now in v2.9, as we have found work-arounds for the errata. However, as usual, your mileage may vary. Be prepared for un-bricking, if it all goes pear shaped.
I have updated v1.3.4 of the RUC to reflect this.

notinthisworld, if you download 1.3.4 of the RUC again and run it, you should be told which firmware package to use

thanks for the help sir

brylok1981 · Post by **brylok1981** » Mon Apr 20, 2009 1:42 pm

my router reboot after some time

i suspect poor line quality

Code: Select all

ADSL Modem information

AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
	US Connection Rate:	320	DS Connection Rate:	1312
	DS Line Attenuation:	15	DS Margin:		31
	US Line Attenuation:	2	US Margin:		23
	US Payload :		41992272	DS Payload:		3232560
	US Superframe Cnt :	94023	DS Superframe Cnt:	94023
	US Transmit Power :	11	DS Transmit Power:	0
	LOS errors:		0	SEF errors:		0
	Errored Seconds:	0	Severely Err Secs:	0
	Frame mode:		3	Max Frame mode:		0
	Trained Path:		0	US Peak Cell Rate:	754
	Trained Mode:		3	Selected Mode:		3
	ATUC Vendor Code:	4946544E	ATUC Revision:	1
	Hybrid Selected:	1	Trellis:		1
	Showtime Count:		1	DS Max Attainable Bit Rate: 10400 kbps
	BitSwap:		1	US Max Attainable Bit Rate:	n/a
	Annex: 			AnxA	psd_mask_qualifier: 0x0000
	ATUC ghsVid:  b5 00 49 46 54 4e 31 94
	T1413Vid: 00 00		T1413Rev: 00		VendorRev: 00
	ATUR ghsVid:  b5 00 54 53 54 43 00 00
	T1413Vid: 00 00	T1413Rev: 00	VendorRev: 00

	[Upstream (TX) Interleave path]
	CRC: 	0	FEC: 	0	NCD: 	1
	LCD: 	0	HEC: 	0

	[Downstream (RX) Interleave path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Upstream (TX) Fast path]
	CRC: 	1	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Downstream (RX) Fast path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

[ATM Stats]
	[Upstream/TX]
	Good Cell Cnt:	874839
	Idle Cell Cnt:	331493


	[Downstream/RX)]
	Good Cell Cnt:	67345
	Idle Cell Cnt:	4878609
	Bad Hec Cell Cnt:	0
	Overflow Dropped Cell Cnt:	0

[SAR AAL5 Stats]
	Tx PDU's:	38237
	Rx PDU's:	22612
	Tx Total Bytes:	41436446
	Rx Total Bytes:	2731730
	Tx Total Error Counts:	0
	Rx Total Error Counts:	0


[OAM Stats]
	Near End F5 Loop Back Count:	0
	Near End F4 Loop Back Count:	0
	Far End F5 Loop Back Count:	0
	Far End F4 Loop Back Count:	0
	SAR OAM Ping Response Drop Count=15

status was generated at about 30 minutes after modem was connected

Chris_TG · Post by **Chris_TG** » Mon Apr 20, 2009 2:26 pm

@thechief: Any news on the Annex-B version? Is there yet something to test again? (sorry, I'm not good in patience, I know *g*

)

Post by **thechief** » Mon Apr 20, 2009 2:50 pm

Chris_TG wrote:@thechief: Any news on the Annex-B version? Is there yet something to test again? (sorry, I'm not good in patience, I know *g* )

Rebuilt last night. Should be online sometime sometime later today or tomorrow.

Post by **Kieran** » Mon Apr 20, 2009 9:30 pm

thechief wrote:
Chris_TG wrote:@thechief: Any news on the Annex-B version? Is there yet something to test again? (sorry, I'm not good in patience, I know *g* )
Rebuilt last night. Should be online sometime sometime later today or tomorrow.

The download thread has now been updated with this rebuild. Sorry for the delay.

Chris_TG · Post by **Chris_TG** » Mon Apr 20, 2009 9:47 pm

Great, many thanks! I will try it out now

mysticalos · Post by **mysticalos** » Tue Apr 21, 2009 1:24 am

I could not find command to set driver to 7.05 it's in release notes but not how to enable it. It also wasn't in command list in router either.

RouterTech Firmware 2.9 Discussion

Re: Asmax AR 804gu (Solwise SAR-600EW ADSL2/2+)

Re: Asmax AR 804gu (Solwise SAR-600EW ADSL2/2+)

Re: Asmax AR 804gu (Solwise SAR-600EW ADSL2/2+)

Asmax AR 804gu possible line poor quality rt 2.9