I bricked my aztech dsl 605ew
I bricked my aztech dsl 605ew
The router doesn't seem to accept any firmware anymore. The router repair tool says flashing was succesfull and waits for router after reboot and just stays like that. Pc-tool just crashes after sending the firmware file. This all started to happen when i tried to restore env backup. And the router's internet led just keeps blinking even though there is no phone line. (it only blinks after successful dsl connection. )
Edit: I have successfully used this firmware before "routertech-ar7wrd-1350A-pspboot-firmware-20100818"
Edit: I tried pc-tool 2.1 and before flashing it said mtd4 was missing and then hanged.
Edit: I have successfully used this firmware before "routertech-ar7wrd-1350A-pspboot-firmware-20100818"
Edit: I tried pc-tool 2.1 and before flashing it said mtd4 was missing and then hanged.
Re: I bricked my aztech dsl 605ew
I fixed it by creating a new env file with firmware tool and uploaded it using pc-tool. What I don't understand is I used the env file I created with 2.94 firmware and later used it on 2.94 again. This, for some reason prevented router from booting.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: I bricked my aztech dsl 605ew
Post that env here.Kaan wrote:What I don't understand is I used the env file I created with 2.94 firmware and later used it on 2.94 again. This, for some reason prevented router from booting.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: I bricked my aztech dsl 605ew
This env is a bit messy because I had lost the original one. I added most of the missing things later myself to fix wireless.
Code: Select all
setenv BUILD_OPS 0x301
setenv bootloaderVersion 1.4.0.4
setenv ProductID AR7WRD
setenv IPA 192.168.1.1
setenv MAC_PORT 0
setenv MEMSZ 0x01000000
setenv FLASHSZ 0x00400000
setenv MODETTY0 9600,n,8,1,hw
setenv MODETTY1 9600,n,8,1,hw
setenv CPUFREQ 211968000
setenv MIPSFREQ 211968000
setenv SYSFREQ 105984000
setenv BOOTCFG m:f:"mtd1"
setenv PROMPT (psbl)
setenv mtd2 0x90000000,0x90010000
setenv mtd3 0x90010000,0x90020000
setenv DSL_BIT_TMODE 1
setenv DSL_UPG_DONE 1
setenv vcc_encaps0 0.0
setenv vcc_encaps1 0.0
setenv vcc_encaps2 0.0
setenv vcc_encaps3 0.0
setenv vcc_encaps4 0.0
setenv vcc_encaps5 0.0
setenv vcc_encaps6 0.0
setenv vcc_encaps7 0.0
setenv autopvc_enable 1
setenv pppoe_relay_enabled 1
setenv sar_ipacemax 6
setenv HWRevision 402H
setenv usb_vid 0x0451
setenv usb_pid 0x6060
setenv HWA_RNDIS 00:E0:A6:66:41:EB
setenv HWA_HRNDIS 00:E0:A6:66:41:E1
setenv FirstUseDate 2002-09-08T12:01:21
setenv mtd1 0x90020090,0x900A0000
setenv WLAN_HWADDR 00:50:f1:12:12:10
setenv autoload 0
setenv mtd5 0x903c0000,0x90400000
setenv RT_init_nvram mount -t minix /dev/mtdblock/5 /nvram/
setenv mtd0 0x900A0000,0x90400000
setenv mtd4 0x90020000,0x90400000
setenv WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D54101212F1
setenv WLAN_EEPROM1 50000000013984000100000101854C1068900105850600100001298507000000
setenv WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
setenv WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
setenv WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
setenv WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
setenv WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
setenv WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
setenv WLAN_EEPROM8 1401C2475064017C0502000036006D00A600E5000404441016004510F903185A
setenv WLAN_EEPROM9 4000145A2000020E0801E6000A0188026E00A30185095000F9000A01C1026E00
setenv WLAN_EEPROM10 A10185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
setenv WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
setenv WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
setenv WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
setenv WLAN_EEPROM14 00000000000000000000000000000000000000000000000000
setenv led_conf /nvram/led
setenv vlynq_polarity low
setenv NVS_TFTP_LOAD 0
setenv IPA_SVR 192.168.1.2
setenv StaticBuffer 384
setenv SerialNumber 2505093301155
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: I bricked my aztech dsl 605ew
Looks alright to me (except for this "setenv autoload 0" - I don't think your bootloader understands that, but for Adam2, it is telling the router not to load the kernel and filesystem, meaning you have to load them manually, from a serial console).
I think the real question is how you tried to restore this env. If you try it from the router (e.g., in a telnet session), then the file that you use has to be in unix format, otherwise the commands will just be messed up (and that could well trash your env).
I think the real question is how you tried to restore this env. If you try it from the router (e.g., in a telnet session), then the file that you use has to be in unix format, otherwise the commands will just be messed up (and that could well trash your env).
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: I bricked my aztech dsl 605ew
That's exactly what happened with rrt using telnet. Only when i discovered that i can do the same with pctool that i fixed my problem. I kinda thought about file format, should have tried changing it.
Re: I bricked my aztech dsl 605ew
BTW Version 1.0.8 now handles PCTool scripts which are saved in Unix file format (in case that was the problem).
RouterTech Team and Founding Member
RouterTech Merchandise (UK)
No support via PM, please ask your questions on the forum!
RouterTech Merchandise (UK)
No support via PM, please ask your questions on the forum!
Re: I bricked my aztech dsl 605ew
Thanks, although the env file i used was created with ruc, rrt still corrupted it for some reason.
Re: I bricked my aztech dsl 605ew
Ah, maybe there is something else unusual in the script then. My guess would be the line
which has quotation marks in it.
I have tweaked version 1.0.8 to look for and escape these now.
Code: Select all
setenv BOOTCFG m:f:"mtd1"
I have tweaked version 1.0.8 to look for and escape these now.
RouterTech Team and Founding Member
RouterTech Merchandise (UK)
No support via PM, please ask your questions on the forum!
RouterTech Merchandise (UK)
No support via PM, please ask your questions on the forum!
Re: I bricked my aztech dsl 605ew
I have that line on my current working env, there is nothing wrong with it right? Actually can you look through that env and tell me if there is anything wrong with it? I have system call errors when my router tries to connect with ppoa. I only have 1 connection setup. I tried to reset again but can't produce that error now because my router doesn't sync for some reason. My other router is syncing fine.
And the log, i have Multi_Mode selected.setenv BUILD_OPS 0x301
setenv CPUFREQ 211968000
setenv MIPSFREQ 211968000
setenv SYSFREQ 105984000
setenv vlynq_polarity low
setenv NVS_TFTP_LOAD 0
setenv MEMSZ 0x01000000
setenv FLASHSZ 0x00400000
setenv mtd1 0x90020090,0x900a1000
setenv mtd2 0x90000000,0x90010000
setenv mtd3 0x90010000,0x90020000
setenv IPA 192.168.1.1
setenv IPA_SVR 192.168.1.2
setenv DSL_BIT_TMODE 1
setenv DSL_UPG_DONE 1
setenv BOOTCFG m:f:"mtd1"
setenv sar_ipacemax 6
setenv autopvc_enable 1
setenv pppoe_relay_enabled 1
setenv configid 3
setenv vcc_encaps0 0.0
setenv vcc_encaps1 0.0
setenv vcc_encaps2 0.0
setenv vcc_encaps3 0.0
setenv vcc_encaps4 0.0
setenv vcc_encaps5 0.0
setenv vcc_encaps6 0.0
setenv vcc_encaps7 0.0
setenv PROMPT psbl>
setenv WLAN_HWADDR0 00:50:f1:12:12:10
setenv wan_br_mac 00:50:f1:12:12:10
setenv WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D54101212F1
setenv WLAN_EEPROM1 50000000013984000100000101854C1068900105850600100001298507000000
setenv WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
setenv WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
setenv WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
setenv WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
setenv WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
setenv WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
setenv WLAN_EEPROM8 1401C2475064017C0502000036006D00A600E5000404441016004510F903185A
setenv WLAN_EEPROM9 4000145A2000020E0801E6000A0188026E00A30185095000F9000A01C1026E00
setenv WLAN_EEPROM10 A10185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
setenv WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
setenv WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
setenv WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
setenv bootloaderVersion 1.4.0.4
setenv ProductID AR7WRD
setenv MAC_PORT 0
setenv mtd0 0x900a1000,0x903f0000
setenv mtd4 0x90020000,0x903f0000
setenv mtd5 0x903f0000,0x90400000
setenv RT_init_nvram mount -t minix /dev/mtdblock/5 /nvram/
setenv led_conf /nvram/led
setenv HWRevision 402H
setenv SerialNumber 2505093301155
setenv MODETTY0 9600,n,8,1,hw
setenv MODETTY1 9600,n,8,1,hw
setenv StaticBuffer 384
setenv autoload 0
setenv modulation 0x24ff
Code: Select all
Aug 18 11:34:25 cfgmgr(sar): DSL Carrier is down
Aug 18 11:34:25 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: I bricked my aztech dsl 605ew
That is not multi_mode.setenv modulation 0x24ff
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: I bricked my aztech dsl 605ew
Strange, firmware tool generated that setting. I looked at multimode under modem options and all of them were checked. And under modem status page router was trying to connect every mode possible. I should still remove that though.
Edit: I just checked firmware tool and there was no modulation setting. I have no idea where that setting came from. Router still doesn't sync though. I called my isp and expecting a solution. Wonder why this other broadcom based router is syncing ok.
Edit: I just checked firmware tool and there was no modulation setting. I have no idea where that setting came from. Router still doesn't sync though. I called my isp and expecting a solution. Wonder why this other broadcom based router is syncing ok.
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: I bricked my aztech dsl 605ew
Without seeing the system diagnostics, I can't comment. But you can't rule out a partly failed upgrade, or a hardware issue.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.
Re: I bricked my aztech dsl 605ew
Here is the system diagnostics. It's most likely a hardware issue i think.
Code: Select all
ROUTERTECH SYSTEM DIAGNOSTICS
Operating system version
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers@RouterTech.Org) #80 Wed Aug 18 11:29:38 BST 2010
Firmware version information
BUILD=RouterTech_3.7.1B_1350A_20100818_2.94_AR7WRD_psbl
VERSION=1350A_20100818
BOARD=AR7WRD
TARGET=psbl
FSSTAMP=20100818113358
PSP version information
Linux OS DSL-PSP 5.2.1.1 on DEV_BasePSP7.4.4.24_Patch compiled at Aug 18 2010 11:30:39
Avalanche SOC Version: 0x11002b
Operating in cached, write back, write allocate mode
CPU Frequency: 211968000 Hz
System Bus frequency: 105984000 Hz
VBUS frequency: 52992000 Hz
Driver version information
Core Logic version: 3.7.1B
Texas Instruments : CPMAC Linux DDA version 1.9
Texas Instruments : CPMAC DDC version 0.3
ATM Driver version:[7.01.00.10]
DSL HAL version: [7.01.00.08]
DSP Datapump version: [7.01.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
Modem Modulation Information
NO_MODE 0x0
ADSL_G.dmt 0x2
ADSL_G.lite 0x4
ADSL_G.dmt.bis 0x8
ADSL_G.dmt.bis_DELT 0x9
ADSL_2plus 0x10
ADSL_2plus_DELT 0x11
ADSL_re-adsl 0x20
ADSL_re-adsl_DELT 0x21
ADSL_ANSI_T1.413 0x80
MULTI_MODE 0xff
ADSL_G.dmt.bis_AnxI 0x0
ADSL_G.dmt.bis_AnxJ 0x0
ADSL_G.dmt.bis_AnxM 0x400
ADSL_2plus_AnxI 0x0
ADSL_2plus_AnxJ 0x0
ADSL_2plus_AnxM 0x2000
G.shdsl 0x0
IDSL 0x0
HDSL 0x0
SDSL 0x0
VDSL 0x0
System environment (/proc/ticfg/env)
autoload 0
autopvc_enable 1
BOOTCFG m:f:"mtd1"
bootloaderVersion 1.4.0.4
BUILD_OPS 0x301
configid 3
CPUFREQ 211968000
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
FLASHSZ 0x00400000
HWRevision 402H
IPA 192.168.1.1
IPA_SVR 192.168.1.2
led_conf /nvram/led
MAC_PORT 0
MEMSZ 0x01000000
MIPSFREQ 211968000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
modulation 0xff
mtd0 0x900a1000,0x903f0000
mtd1 0x90020090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x903f0000
mtd5 0x903f0000,0x90400000
NVS_TFTP_LOAD 0
pppoe_relay_enabled 1
ProductID AR7WRD
PROMPT psbl>
RT_init_nvram mount -t minix /dev/mtdblock/5 /nvram/
sar_ipacemax 6
SerialNumber 2505093301155
StaticBuffer 384
SYSFREQ 105984000
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
vlynq_polarity low
wan_br_mac 00:50:f1:12:12:10
WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D54101212F1
WLAN_EEPROM1 50000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM10 A10185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM8 1401C2475064017C0502000036006D00A600E5000404441016004510F903185A
WLAN_EEPROM9 4000145A2000020E0801E6000A0188026E00A30185095000F9000A01C1026E00
WLAN_HWADDR0 00:50:f1:12:12:10
CPU information
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
Memory (RAM) information
total: used: free: shared: buffers: cached:
Mem: 14528512 11714560 2813952 0 1433600 4767744
Swap: 0 0 0
MemTotal: 14188 kB
MemFree: 2748 kB
MemShared: 0 kB
Buffers: 1400 kB
Cached: 4656 kB
SwapCached: 0 kB
Active: 1784 kB
Inactive: 5912 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 14188 kB
LowFree: 2748 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Flash memory (chip) information
Flash type: AMD; Manufacturer=MACRONIX (AMD-compat).
Manufacturer_ID=0x00C2; Chip_ID=0x00A8; Chip_Size=0x400000; Erase_Regions=0x0002
Mount points
/dev/mtdblock/0 / squashfs ro 0 0
none /dev devfs rw 0 0
proc /proc proc rw 0 0
ramfs /var ramfs rw 0 0
/dev/mtdblock/5 /nvram minix rw 0 0
Filesystems
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev shm
nodev pipefs
nodev ramfs
minix
nodev devfs
squashfs
MTD
dev: size erasesize name
mtd0: 0034f000 00010000 "mtd0"
mtd1: 00080f70 00010000 "mtd1"
mtd2: 00010000 00002000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 003d0000 00010000 "mtd4"
mtd5: 00010000 00010000 "mtd5"
Kernel modules
tiatm 135360 c0032060 96 0 (unused)
Interrupts
7: 125870 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 228 serial [hw0 (Avalanche Primary)]
23: 0 + SAR [hw0 (Avalanche Primary)]
27: 5325 + Cpmac Driver [hw0 (Avalanche Primary)]
29: 0 vlynq0 [hw0 (Avalanche Primary)]
31: 1679 + DSL [hw0 (Avalanche Primary)]
Devices
Character devices:
1 mem
2 pty/m%d
3 pty/s%d
4 tts/%d
5 cua/%d
10 misc
36 netlink
108 ppp
128 ptm
136 pts/%d
162 raw
Block devices:
7 loop
31 mtdblock
Processes
PID USER VSZ STAT COMMAND
1 root 1060 S init
2 root 0 SW [keventd]
3 root 0 SWN [ksoftirqd_CPU0]
4 root 0 SW [kswapd]
5 root 0 SW [bdflush]
6 root 0 SW [kupdated]
7 root 0 SW [mtdblockd]
460 root 2312 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
463 root 2308 S /usr/bin/cm_pc
464 root 5008 S /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
528 root 748 S /sbin/dproxy -c /etc/resolv.conf -d
547 root 1060 S init
671 root 968 S /usr/sbin/udhcpd /var/tmp/udhcpd.conf
999 root 1068 S N /bin/sh diagnostics.cgi
1000 root 2348 S /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
1004 root 632 S N /usr/local/bin/diagnostics
1005 root 1064 S N sh -c /usr/local/bin/diagnostics.sh
1006 root 1068 S N /bin/sh /usr/local/bin/diagnostics.sh
1030 root 1060 R N /bin/ps
ADSL Modem information
AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
US Connection Rate: 0 DS Connection Rate: 0
DS Line Attenuation: 0 DS Margin: 13
US Line Attenuation: 0 US Margin: 0
US Payload : 0 DS Payload: 0
US Superframe Cnt : 0 DS Superframe Cnt: 0
US Transmit Power : 0 DS Transmit Power: 0
LOS errors: 0 SEF errors: 0
Errored Seconds: 0 Severely Err Secs: 0
Frame mode: 3 Max Frame mode: 0
Trained Path: 0 US Peak Cell Rate: 0
Trained Mode: 16 Selected Mode: 65535
ATUC Vendor Code: 4244434D ATUC Revision: 2
Hybrid Selected: 1 Trellis: 1
Showtime Count: 0 DS Max Attainable Bit Rate: 11760 kbps
BitSwap: 1 US Max Attainable Bit Rate: 0 bps
Annex: AnxA psd_mask_qualifier: 0x0000
Power Management Status: L3 DS HLINSC: 2260
US ACTPSD: 0 DS ACTPSD: 0
Total init. errors: 68 Total init. timeouts: 0
Showtime init. errors: 68 Showtime init. timeouts: 0
Last showtime init. errors: 68 Last showtime init. timeouts: 0
ATUC ghsVid: b5 00 42 44 43 4d 62 91
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
ATUR ghsVid: b5 00 54 53 54 43 00 00
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
[Upstream (TX) Interleave path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Downstream (RX) Interleave path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Upstream (TX) Fast path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[Downstream (RX) Fast path]
CRC: 0 FEC: 0 NCD: 0
LCD: 0 HEC: 0
[ATM Stats]
[Upstream/TX]
Good Cell Cnt: 0
Idle Cell Cnt: 0
Tx Packets Dropped Count: 0
Tx Bad Packets Count: 0
[Downstream/RX)]
Good Cell Cnt: 0
Idle Cell Cnt: 0
Bad Hec Cell Cnt: 0
Overflow Dropped Cell Cnt: 0
Rx Packets Dropped Count: 0
Rx Bad Packets Count: 0
[SAR AAL5 Stats]
Tx PDU's: 0
Rx PDU's: 0
Tx Total Bytes: 0
Rx Total Bytes: 0
Tx Total Error Counts: 0
Rx Total Error Counts: 0
[OAM Stats]
Near End F5 Loop Back Count: 0
Near End F4 Loop Back Count: 0
Far End F5 Loop Back Count: 0
Far End F4 Loop Back Count: 0
SAR OAM Ping Response Drop Count=0
Trained modulation:
ADSL_2plus
Path mode:
FastPath
Network statistics
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State
tcp 0 0 0.0.0.0:www 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:domain 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ftp 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:telnet 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:1050 0.0.0.0:* LISTEN
tcp 0 573 mygateway1.AR7WRD:www 192.168.1.2:9872 ESTABLISHED
tcp 0 0 mygateway1.AR7WRD:www 192.168.1.2:9870 TIME_WAIT
udp 0 0 0.0.0.0:domain 0.0.0.0:*
udp 0 0 0.0.0.0:bootps 0.0.0.0:*
udp 0 0 0.0.0.0:tftp 0.0.0.0:*
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags Type State I-Node Path
unix 2 [ ] DGRAM 514 /var/tmp/cm_pc.ctl
unix 2 [ ] DGRAM 531 /var/tmp/cm_logic.ctl
unix 3 [ ] DGRAM 544 /dev/log
unix 2 [ ] DGRAM 504 /var/tmp/cm_miniHttpd.ctl
unix 2 [ ] DGRAM 1050
unix 2 [ ] STREAM 500
unix 2 [ ] DGRAM 499
unix 2 [ ] DGRAM 26
Iptables chains
Chain INPUT (policy ACCEPT 1173 packets, 371K bytes)
pkts bytes target prot opt in out source destination
381 32908 CFG tcp -- any any 192.168.1.2 anywhere tcp dpt:www Records Packet's Source Interface
0 0 CFG tcp -- any any 192.168.1.2 anywhere tcp dpt:443 Records Packet's Source Interface
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
0 0 DROP icmp -f any any anywhere anywhere
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
0 0 TCPMSS tcp -- any any anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU
Chain OUTPUT (policy ACCEPT 1809 packets, 477K bytes)
pkts bytes target prot opt in out source destination
0 0 ACCEPT icmp -- any any anywhere anywhere icmp fragmentation-needed
Network interface details
br0 Link encap:Ethernet HWaddr 08:00:28:32:06:02
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5476 errors:0 dropped:0 overruns:0 frame:0
TX packets:1896 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:792373 (773.8 KiB) TX bytes:516578 (504.4 KiB)
br1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br2 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br3 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 08:00:28:32:06:02
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5560 errors:0 dropped:0 overruns:0 frame:0
TX packets:1879 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:804722 (785.8 KiB) TX bytes:504928 (493.0 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
System Log
Aug 18 11:34:15 cfgmgr(sar): Could not get oam_ping_interval from boot loader env
Aug 18 11:34:15 cfgmgr(sar): Trying to retreive the value from Configuration
Aug 18 11:34:15 cfgmgr(sar): oamPingInterval(20)(20)
Aug 18 11:34:15 cfgmgr(ap): AP is disabled
Aug 18 11:34:15 cfgmgr(pppoa-109): Valid Configuration Tree
Aug 18 11:34:15 cfgmgr(resolver): stat successfull for /etc/resolv.conf.
Aug 18 11:34:15 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Aug 18 11:34:15 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Aug 18 11:34:15 cfgmgr(sar): DSL Polling Timer Started succesfully.
Aug 18 11:34:15 cfgmgr(fdb): Firewall NAT service started
Aug 18 11:34:15 cfgmgr(lanbridge0): Bridge Created: br0
Aug 18 11:34:17 cfgmgr(lanbridge1): Bridge Created: br1
Aug 18 11:34:19 cfgmgr(lanbridge2): Bridge Created: br2
Aug 18 11:34:20 cfgmgr(lanbridge3): Bridge Created: br3
Aug 18 11:34:22 cfgmgr(lanbridge0): Bridge Interface Added: eth0
Aug 18 11:34:23 root: USB is disabled
Aug 18 11:34:23 root: rcS not stopped by init. Stopping it ...
Aug 18 11:34:25 cfgmgr(sar): DSL Carrier is down
Aug 18 11:34:25 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
Aug 18 11:37:05 cfgmgr(sar): DSL Carrier is training
Aug 18 11:37:05 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
Aug 18 11:41:15 cfgmgr(sar): DSL Carrier is training
Aug 18 11:41:15 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
Aug 18 11:41:45 cfgmgr(sar): DSL Carrier is training
Aug 18 11:41:45 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
Aug 18 11:49:25 cfgmgr(sar): DSL Carrier is training
Aug 18 11:49:25 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
Miscellaneous information
RouterTech firmware release: 2.94
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers@RouterTech.Org) #80 Wed Aug 18 11:29:38 BST 2010
BUILD=RouterTech_3.7.1B_1350A_20100818_2.94_AR7WRD_psbl
VERSION=1350A_20100818
BOARD=AR7WRD
TARGET=psbl
FSSTAMP=20100818113358
Ethernet ports: 4
Core logic version: 3.7.1B
Boot Loader: PSPboot v1.4.0.4
ATM Driver version:[7.01.00.10]
DSL HAL version: [7.01.00.08]
DSP Datapump version: [7.01.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
Upstream rate (kbps): 0
Downstream rate (kbps): 0
Trained Modulation: NO_MODE
Path Mode: FastPath
System uptime: 0 hr 20 min - 0 day(s), 0 hour(s), 21 minute(s), and 12 second(s) (system 96% idle)
WAN uptime: N/A
WAN IP address: N/A
Bandwidth usage:
Downloads : 0.0000 MB
Uploads : 0.0000 MB
Line attenuation:
DS Line Attenuation: 0 DS Margin: 13
US Line Attenuation: 0 US Margin: 0
Memory usage:
In active use : 40% of 14188 kb
Available : 60% (8580 kb) of 14188 kb (of which 6020 kb is marked as "Inactive" and 2560 kb is free)
Environment fragmentation:
Fragmentation level is "12" (out of 72 records). The threshold is "50".
Connection information: connection1
- thechief
- RouterTech Team
- Posts: 12067
- Joined: Wed Feb 01, 2006 10:22 pm
- Location: England, the Centre of Africa
- Contact:
Re: I bricked my aztech dsl 605ew
pppd is not running - which is a problem. Are you sure you have the right DSP driver? (you are using an Annex A driver). If your connection is Annex A, then I am not sure what the problem is - you might want to try flashing the firmware again.
How many connections do you have?
PS: the env is still fragmented.
How many connections do you have?
PS: the env is still fragmented.
The Chief: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
No support via PM. Ask all questions on the open forum.