RouterTech Firmware 2.96 Discussion

All about firmwares for routers. Support for RouterTech firmwares is here too.
Post Reply
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 9:09 am

void wrote:Thanks for the great work. :)
Thanks :)
void wrote:Upgrade successful, there is a problem,
Modem running for some time, probably a few hours later, http (192.168.1.1) and telnet (192.168.1.1) and ftp (192.168.1.1) all failed, unable to connect.
But the Internet connection is normal, then after restarting the Modem function back to normal, and why?
Post the complete system diagnostics. The one you posted is not complete.
void wrote:In addition [LAN GROUP 1] why only Eth1. Eth2, Eth3, Eth4 not?
That is what is available.
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 9:10 am

paaaja wrote:
thechief wrote:I am not aware of any way of doing so.
Well, for the time being I've just set all the router log levels to "Panic", which hardly ever happens. This way I have my logs empty.
And how will you diagnose any problems that may arise?
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
paaaja
Regular
Regular
Posts: 45
Joined: Fri Jun 04, 2010 5:18 pm

Re: RouterTech Firmware 2.96 Discussion

Post by paaaja » Fri May 20, 2011 12:11 pm

thechief wrote:And how will you diagnose any problems that may arise?
I don't need diagnostics. The router simply works. When problems occur, I'll turn the logging back on. You see, my problem is uptime. I have only 8 MB RAM and when the router runs for a month, logging on becomes difficult and the device responds slowly to commands. When I turn the logging off, I have almost unlimited uptime (limited only by blackouts :D )

Or do you think I should leave the logging on and set a cronjob to run "clearlog.sh" every few days?
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 12:59 pm

paaaja wrote:Or do you think I should leave the logging on and set a cronjob to run "clearlog.sh" every few days?
Yes. Try weekly first, and if that doesn't help, then every 3 days or so. You may also want to run "dmesg -c" at the same time as "clearlog.sh".
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
void
Newbie
Newbie
Posts: 7
Joined: Mon Apr 25, 2011 2:26 am

Re: RouterTech Firmware 2.96 Discussion

Post by void » Fri May 20, 2011 1:23 pm

Post the complete system diagnostics. The one you posted is not complete.
ok,the System Diagnostics output:

Code: Select all

ROUTERTECH SYSTEM DIAGNOSTICS

Client browser information
Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; Trident/5.0)

Router operating system version
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #332 Mon May 2 01:40:13 BST 2011

Firmware version information
BUILD=RouterTech_3.7.1B_1350A_20110502_2.96_AR7WRD_psbl
VERSION=1350A_20110502
BOARD=AR7WRD
TARGET=psbl
FSSTAMP=20110502014434
ROHS=1

PSP version information

Linux OS DSL-PSP 5.2.1.1 on DEV_BasePSP7.4.4.24_Patch compiled at May  2 2011 01:41:15
Avalanche SOC Version: 0x11002b
Operating in cached, write back, write allocate mode
CPU Frequency: 211968000 Hz
System Bus frequency: 105984000 Hz
VBUS frequency: 52992000 Hz


Driver version information
Core Logic version: 3.7.1B
Texas Instruments : CPMAC Linux DDA version 1.9
Texas Instruments : CPMAC DDC version 0.3
ATM Driver version:[7.01.00.10]
DSL HAL version: [7.01.00.08]
DSP Datapump version: [7.01.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]

Modem Modulation Information
NO_MODE			0x0
ADSL_G.dmt			0x2
ADSL_G.lite			0x4
ADSL_G.dmt.bis			0x8
ADSL_G.dmt.bis_DELT			0x9
ADSL_2plus			0x10
ADSL_2plus_DELT			0x11
ADSL_re-adsl			0x20
ADSL_re-adsl_DELT			0x21
ADSL_ANSI_T1.413			0x80
MULTI_MODE			0xff
ADSL_G.dmt.bis_AnxI			0x0
ADSL_G.dmt.bis_AnxJ			0x0
ADSL_G.dmt.bis_AnxM			0x400
ADSL_2plus_AnxI			0x0
ADSL_2plus_AnxJ			0x0
ADSL_2plus_AnxM			0x2000
G.shdsl			0x0
IDSL			0x0
HDSL			0x0
SDSL			0x0
VDSL			0x0

System environment (/proc/ticfg/env)
BUILD_OPS	0x301
bootloaderVersion	1.4.0.4
MODETTY0	115200,n,8,1,hw
MODETTY1	115200,n,8,1,hw
CPUFREQ	211968000
MIPSFREQ	211968000
SYSFREQ	105984000
HWRevision	Gaw7.2Z39-4
MAC_PORT	1
mtd2	0x90000000,0x90010000
HWA_RNDIS	00:E0:A6:66:41:E1
HWA_HRNDIS	00:E0:A6:66:41:E2
BOOTCFG	m:f:"mtd1"
ProductID	AR7WRD
SerialNumber	none
MEMSZ	0x01000000
FLASHSZ	0x00800000
PROMPT	(psbl)
DSL_BIT_TMODE	1
DSL_UPG_DONE	1
vcc_encaps0	0.0
vcc_encaps1	0.0
vcc_encaps2	0.0
vcc_encaps3	0.0
vcc_encaps4	0.0
vcc_encaps5	0.0
vcc_encaps6	0.0
vcc_encaps7	0.0
HWA_0	00:74:04:F1:4E:62
HWA_2	00:74:04:F1:4E:63
HWA_3	00:74:04:F1:4E:63
mac_ap	00:74:04:F1:4E:64
WLAN_HWADDR	00:74:04:F1:4E:64
WLAN_EEPROM0	021156041B06001200000601095612000000010D56A9000000026D54B5000004
WLAN_EEPROM1	74000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM2	01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3	8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4	55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5	0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6	01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7	2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM8	1A0189B5035901ED0502000037007000A800E60004044410FD034510E703185A
WLAN_EEPROM9	4000145A2800020E0801CB000A0198025000C40176095000E6000A01F0025000
WLAN_EEPROM10	9E0176090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11	FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
WLAN_EEPROM12	090909090909090909090909090909090909090909090909090909090909090E
WLAN_EEPROM13	0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM14	00000000000000000000000000000000000000000000000000
NVS_TFTP_LOAD	0
vlynq_polarity	low
Max_MACs	0
connection1	0xe025

connection0	0x772f

connection6	0
TR69_CR_USERNAME	plugfest
TR69_CR_PASSWORD	plugfest
Route_Enabled	1
led_conf	led.generic2
mtd0 1	0x90020090,0x900a1000
IPA	192.168.1.1
mtd4	0x90020000,0x90400000
mtd3	0x90010000,0x90020000
mtd5	0x90420000,0x90800000
autopvc_enable	1
pppoe_relay_enabled	1
StaticBuffer	384
WLAN_HWADDR0	00:74:04:F1:4E:64
WLAN_HWADDR1	02:30:1A:F1:4E:64
WLAN_HWADDR2	02:30:2A:F1:4E:64
WLAN_HWADDR3	02:30:3A:F1:4E:64
sar_ipacemax	6
configid	1
mtd1	0x90020090,0x900a1000
mtd0	0x900a1000,0x90400000

CPU information
processor		: 0
cpu model		: MIPS 4KEc V4.8
BogoMIPS		: 211.35
wait instruction	: no
microsecond timers	: yes
extra interrupt vector	: yes
hardware watchpoint	: yes
VCED exceptions		: not available
VCEI exceptions		: not available

Memory (RAM) information
        total:    used:    free:  shared: buffers:  cached:
Mem:  14512128 12165120  2347008        0  1531904  5074944
Swap:        0        0        0
MemTotal:        14172 kB
MemFree:          2292 kB
MemShared:           0 kB
Buffers:          1496 kB
Cached:           4956 kB
SwapCached:          0 kB
Active:           1744 kB
Inactive:         6492 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        14172 kB
LowFree:          2292 kB
SwapTotal:           0 kB
SwapFree:            0 kB

Flash memory (chip) information
Flash_type=AMD; Manufacturer=Unknown!.
Manufacturer_ID=0x007F; Chip_ID=0x007E; Chip_Size=0x800000; Erase_Regions=0x0001

Mount points
/dev/mtdblock/0 / squashfs ro 0 0
none /dev devfs rw 0 0
proc /proc proc rw 0 0
ramfs /var ramfs rw 0 0

Filesystems
nodev	rootfs
nodev	bdev
nodev	proc
nodev	sockfs
nodev	tmpfs
nodev	shm
nodev	pipefs
nodev	ramfs
	minix
nodev	devfs
	squashfs

MTD
dev:    size   erasesize  name
mtd0: 0035f000 00010000 "mtd0"
mtd1: 00080f70 00010000 "mtd1"
mtd2: 00010000 00010000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 003e0000 00010000 "mtd4"

Kernel modules
tiatm                 135360 c0021060 96    1

Interrupts
  7:     6000   R4000 timer/counter [MIPS interrupt]
  8:        0   unified secondary [hw0 (Avalanche Primary)]
 15:      301   serial [hw0 (Avalanche Primary)]
 23:       24 + SAR  [hw0 (Avalanche Primary)]
 27:      113 + Cpmac Driver [hw0 (Avalanche Primary)]
 29:        0   vlynq0 [hw0 (Avalanche Primary)]
 31:       49 + DSL  [hw0 (Avalanche Primary)]

Devices
Character devices:
  1 mem
  2 pty/m%d
  3 pty/s%d
  4 tts/%d
  5 cua/%d
 10 misc
 36 netlink
108 ppp
128 ptm
136 pts/%d
162 raw

Block devices:
  7 loop
 31 mtdblock

Serial port information
serinfo:1.0 driver:5.05c revision:2001-07-08
0: uart:16550A port:A8610E00 irq:15 baud:7944 tx:4471 rx:0 RTS|DTR
1: uart:unknown port:A8610F00 irq:16

Processes
  PID USER       VSZ STAT COMMAND
    1 root      1060 S    init
    2 root         0 SW   [keventd]
    3 root         0 SWN  [ksoftirqd_CPU0]
    4 root         0 SW   [kswapd]
    5 root         0 SW   [bdflush]
    6 root         0 SW   [kupdated]
    7 root         0 SW   [mtdblockd]
  556 root      2308 S    /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
  557 root      2248 S    /usr/bin/cm_pc
  559 root      5016 S    /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
  637 root      1060 S    init
  668 root       748 S    /sbin/dproxy -c /etc/resolv.conf -d
  868 root       968 S    /usr/sbin/udhcpd /var/tmp/udhcpd.conf
  885 root      1072 S N  /bin/sh diagnostics.cgi
  886 root      2352 S    /usr/sbin/mini_httpd -d /usr/www -u root -p 80 -c /c
  891 root      1236 S N  /usr/local/bin/diagnostics
  892 root      1064 S N  sh -c /usr/local/bin/diagnostics.sh
  893 root      1128 S N  /bin/bash /usr/local/bin/diagnostics.sh
  910 root      2676 S    /usr/sbin/pppd plugin pppoa 0.38 user user@ispname p
  942 root      1060 R N  /bin/ps

ADSL Modem information

AR7 DSL Modem Statistics:
--------------------------------
[DSL Modem Stats]
	US Connection Rate:	384	DS Connection Rate:	2048
	DS Line Attenuation:	44	DS Margin:		18
	US Line Attenuation:	17	US Margin:		26
	US Payload :		720	DS Payload:		864
	US Superframe Cnt :	601	DS Superframe Cnt:	601
	US Transmit Power :	12	DS Transmit Power:	16
	LOS errors:		0	SEF errors:		0
	Errored Seconds:	0	Severely Err Secs:	0
	Frame mode:		3	Max Frame mode:		0
	Trained Path:		1	US Peak Cell Rate:	905
	Trained Mode:		2	Selected Mode:		65535
	ATUC Vendor Code:	4753504E	ATUC Revision:	1
	Hybrid Selected:	3	Trellis:		1
	Showtime Count:		1	DS Max Attainable Bit Rate: 5376 kbps
	BitSwap:		1	US Max Attainable Bit Rate:	n/a
	Annex: 			AnxA	psd_mask_qualifier: 0x0000
	Power Management Status: L0	DS HLINSC: 0
	US ACTPSD: 		-345	DS ACTPSD: -371
	Total init. errors: 	0	Total init. timeouts: 0
	Showtime init. errors: 	0	Showtime init. timeouts: 0
	Last showtime init. errors: 0	Last showtime init. timeouts: 0
	ATUC ghsVid:  ff b5 47 53 50 4e 00 07
	T1413Vid: 00 00		T1413Rev: 00		VendorRev: 00
	ATUR ghsVid:  b5 00 54 53 54 43 00 00
	T1413Vid: 00 00	T1413Rev: 00	VendorRev: 00

	[Upstream (TX) Interleave path]
	CRC: 	1	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	68

	[Downstream (RX) Interleave path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

	[Upstream (TX) Fast path]
	CRC: 	0	FEC: 	0	NCD: 	1
	LCD: 	0	HEC: 	0

	[Downstream (RX) Fast path]
	CRC: 	0	FEC: 	0	NCD: 	0
	LCD: 	0	HEC: 	0

[ATM Stats]
	[Upstream/TX]
	Good Cell Cnt:	15
	Idle Cell Cnt:	9238

	Tx Packets Dropped Count:	0
	Tx Bad Packets Count:	0

	[Downstream/RX)]
	Good Cell Cnt:	18
	Idle Cell Cnt:	49302
	Bad Hec Cell Cnt:	0
	Overflow Dropped Cell Cnt:	0
	Rx Packets Dropped Count:	0
	Rx Bad Packets Count:	0


[SAR AAL5 Stats]
	Tx PDU's:	1
	Rx PDU's:	0
	Tx Total Bytes:	16
	Rx Total Bytes:	0
	Tx Total Error Counts:	0
	Rx Total Error Counts:	0


[OAM Stats]
	Near End F5 Loop Back Count:	0
	Near End F4 Loop Back Count:	0
	Far End F5 Loop Back Count:	0
	Far End F4 Loop Back Count:	0
	SAR OAM Ping Response Drop Count=15

Modem DSL link information
SHOWTIME
1
failTrains=2

Trained modulation: 
ADSL_G.dmt

Path mode: 
Interleaved

Network statistics
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       
tcp        0      0 0.0.0.0:2048            0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:www             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:domain          0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:ftp             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:ssh             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:telnet          0.0.0.0:*               LISTEN      
tcp        0      0 mygateway1.AR7WRD:www   192.168.1.5:4524        TIME_WAIT   
tcp        0      0 mygateway1.AR7WRD:www   192.168.1.5:4526        TIME_WAIT   
tcp        0      0 mygateway1.AR7WRD:www   192.168.1.5:4525        TIME_WAIT   
tcp        0    832 mygateway1.AR7WRD:www   192.168.1.5:4527        ESTABLISHED 
tcp        0      0 mygateway1.AR7WRD:www   192.168.1.5:4523        TIME_WAIT   
udp        0      0 0.0.0.0:domain          0.0.0.0:*                           
udp        0      0 0.0.0.0:bootps          0.0.0.0:*                           
udp        0      0 0.0.0.0:tftp            0.0.0.0:*                           
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags       Type       State         I-Node Path
unix  4      [ ]         DGRAM                       681 /dev/log
unix  2      [ ]         DGRAM                       632 /var/tmp/cm_miniHttpd.ctl
unix  2      [ ]         DGRAM                       642 /var/tmp/cm_pc.ctl
unix  2      [ ]         DGRAM                       659 /var/tmp/cm_logic.ctl
unix  2      [ ]         DGRAM                      1281 
unix  2      [ ]         DGRAM                      1210 
unix  2      [ ]         STREAM                      628 
unix  2      [ ]         DGRAM                       627 
unix  2      [ ]         DGRAM                        26 

Iptables chains
Chain PREROUTING (policy ACCEPT 32 packets, 2761 bytes)
 pkts bytes target     prot opt in     out     source               destination         

Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination         
    0     0 MASQUERADE  all  --  *      ppp0    0.0.0.0/0            0.0.0.0/0          

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination         

Chain INPUT (policy ACCEPT 105 packets, 7513 bytes)
 pkts bytes target     prot opt in     out     source               destination         
   90  5189 CFG        tcp  --  any    any     192.168.1.5          anywhere           tcp dpt:www Records Packet's Source Interface 

    0     0 CFG        tcp  --  any    any     192.168.1.5          anywhere           tcp dpt:443 Records Packet's Source Interface 

    0     0 ACCEPT     icmp --  any    any     anywhere             anywhere           icmp fragmentation-needed 
    0     0 DROP       icmp -f  any    any     anywhere             anywhere           

Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination         
    0     0 ACCEPT     icmp --  any    any     anywhere             anywhere           icmp fragmentation-needed 
    0     0 TCPMSS     tcp  --  any    any     anywhere             anywhere           tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU 

Chain OUTPUT (policy ACCEPT 173 packets, 128K bytes)
 pkts bytes target     prot opt in     out     source               destination         
    0     0 ACCEPT     icmp --  any    any     anywhere             anywhere           icmp fragmentation-needed 
    0     0 DROP       icmp --  any    ppp0    anywhere             anywhere           icmp destination-unreachable 
    0     0 DROP       icmp --  any    ppp0    anywhere             anywhere           state INVALID 

Network interface details
br0       Link encap:Ethernet  HWaddr 00:74:04:F1:4E:62  
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:107 errors:0 dropped:0 overruns:0 frame:0
          TX packets:176 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:9661 (9.4 KiB)  TX bytes:131909 (128.8 KiB)

br1       Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

br2       Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

br3       Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 00:74:04:F1:4E:62  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:156 errors:0 dropped:0 overruns:0 frame:0
          TX packets:159 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:13943 (13.6 KiB)  TX bytes:118718 (115.9 KiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


System Log
May  2 01:44:17 cfgmgr(sar):  Could not get oam_ping_interval from boot loader env  
May  2 01:44:17 cfgmgr(sar):  Trying to retreive the value from Configuration  
May  2 01:44:17 cfgmgr(sar): oamPingInterval(20)(20) 
May  2 01:44:17 cfgmgr(logic): instantiate_module: module 'eth' couldn't initialize itself 
May  2 01:44:17 cfgmgr(logic): endElement: couldn't instantiate the module 'eth1' 
May  2 01:44:17 cfgmgr(logic): instantiate_module: module 'eth' couldn't initialize itself 
May  2 01:44:17 cfgmgr(logic): endElement: couldn't instantiate the module 'eth2' 
May  2 01:44:17 cfgmgr(logic): instantiate_module: module 'eth' couldn't initialize itself 
May  2 01:44:17 cfgmgr(logic): endElement: couldn't instantiate the module 'eth3' 
May  2 01:44:17 cfgmgr(ap): AP is disabled 
May  2 01:44:17 cfgmgr(pppoa-109): Valid Configuration Tree 
May  2 01:44:17 cfgmgr(logic): couldn't find dependent module 'eth1' 
May  2 01:44:17 cfgmgr(logic): couldn't find dependent module 'eth2' 
May  2 01:44:17 cfgmgr(logic): couldn't find dependent module 'eth3' 
May  2 01:44:17 cfgmgr(logic): couldn't find module 'eth1' 
May  2 01:44:17 cfgmgr(logic): couldn't find module 'eth2' 
May  2 01:44:17 cfgmgr(logic): couldn't find module 'eth3' 
May  2 01:44:17 cfgmgr(resolver): stat successfull for /etc/resolv.conf. 
May  2 01:44:17 cfgmgr(resolver): Resolver Polling Timer Started succesfully. 
May  2 01:44:17 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully. 
May  2 01:44:17 cfgmgr(sar): DSL Polling Timer Started succesfully. 
May  2 01:44:18 cfgmgr(fdb): Firewall NAT service started 
May  2 01:44:18 cfgmgr(lanbridge0): Bridge Created: br0 
May  2 01:44:20 cfgmgr(lanbridge1): Bridge Created: br1 
May  2 01:44:21 cfgmgr(lanbridge2): Bridge Created: br2 
May  2 01:44:22 cfgmgr(lanbridge3): Bridge Created: br3 
May  2 01:44:24 cfgmgr(lanbridge0): Bridge Interface Added: eth0 
May  2 01:44:26 root: USB is disabled  
May  2 01:44:27 cfgmgr(sar): DSL Carrier is down 
May  2 01:44:27 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact  
May  2 01:44:29 webcm: Got group error |Bad username/password| 
May  2 01:44:33 dnsmasq[668]: no servers found in /etc/resolv.conf, will retry 
May  2 01:44:47 cfgmgr(sar): DSL Carrier is up 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.35)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.32)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.40)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.36)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.38)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_default oamPing(0.96)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(0.35)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(8.35)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(0.43)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(0.51)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(0.59)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(8.43)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(8.51)result(2) 
May  2 01:44:47 cfgmgr(sar): auto_vcc_search oamPing(8.59)result(2) 
May  2 01:44:48 pppd[910]: pppd 2.4.4 started by root, uid 0 
May  2 01:44:48 pppd[910]: Connect: ppp0 {--}  
May  2 01:44:51 cfgmgr(pppoa-109): PPPD Successfully Started  

Miscellaneous information
RouterTech firmware release: 2.96
Connecting from: 192.168.1.1 [192.168.1.5]
Router's internal name: mygateway1.AR7WRD
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #332 Mon May 2 01:40:13 BST 2011
BUILD=RouterTech_3.7.1B_1350A_20110502_2.96_AR7WRD_psbl
VERSION=1350A_20110502
BOARD=AR7WRD
TARGET=psbl
FSSTAMP=20110502014434
ROHS=1
Core logic version: 3.7.1B
Boot Loader: PSPboot v1.4.0.4
ATM Driver version:[7.01.00.10]
DSL HAL version: [7.01.00.08]
DSP Datapump version: [7.01.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
Ethernet ports: 4
Upstream rate (kbps):  384
Downstream rate (kbps):  2048
Trained Modulation: ADSL_G.dmt
Path Mode: Interleaved
System uptime: 0hr 0min - 0 day(s), 0 hour(s), 1 minute(s), and 17 second(s) (system 55% idle)
Bandwidth usage:
	Downloads : 0.0000 MB
	Uploads   : 0.0001 MB
Line attenuation: 
	DS Line Attenuation:	44	DS Margin:		18
	US Line Attenuation:	17	US Margin:		26
Memory usage:
	In active use : 40% of 14172 kb
	Available     : 60% (8620 kb) of 14172 kb (of which 6624 kb is marked as "Inactive" and 1996 kb is free)
Environment fragmentation: 
	Fragmentation level is "19" (out of 93 records). The threshold is "50".
Connection information: 
There is no successful connection to the internet.
The existing (unsuccessful) connection(s):
connection0 


 
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 1:32 pm

void wrote:There is no successful connection to the internet.
The existing (unsuccessful) connection(s):
connection0
If there is no connection, then how are you posting this? You should run the system diagnostics when the router is functioning as you would normally be using it (and after about an hour of use).

First of all, defragment your environment.
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
void
Newbie
Newbie
Posts: 7
Joined: Mon Apr 25, 2011 2:26 am

Re: RouterTech Firmware 2.96 Discussion

Post by void » Fri May 20, 2011 3:54 pm

thechief wrote:If there is no connection, then how are you posting this? You should run the system diagnostics when the router is functioning as you would normally be using it (and after about an hour of use).First of all, defragment your environment.
Thanks for your reply!

Do not know why a successful connection is not shown, in fact, I only use the bridge type, do not use other connection type.

Also how to defragment my environment? use 'fixenv' instructions or other operations? Please tell me how to do it.
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 4:09 pm

There is full information in the firmware FAQ about defragmenting - but, yes, "fixenv" is what you need to run.
910 root 2676 S /usr/sbin/pppd plugin pppoa 0.38 user user@ispname p
If you are using a bridged connection, this tells me that you have more than one connection. This can only lead to trouble. Delete the one that you are not using.
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
paaaja
Regular
Regular
Posts: 45
Joined: Fri Jun 04, 2010 5:18 pm

Re: RouterTech Firmware 2.96 Discussion

Post by paaaja » Fri May 20, 2011 7:46 pm

thechief wrote:Yes. You may also want to run "dmesg -c" at the same time as "clearlog.sh".
To be specific, I have in my bootloader settings two options now:
RT_cmd_1 write_crontab.sh '5' '2' '*' '*' '0,2,4,6' 'clearlog.sh'
RT_cmd_2 write_crontab.sh '5' '2' '*' '*' '0,2,4,6' 'dmesg -c'

(Taken from System Diagnostics info.)
Is this OK?
I have only some limited experience with creating cron jobs.
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 7:55 pm

That should be fine, although you might want either to chain the commands

Code: Select all

RT_cmd_1 write_crontab.sh '5' '2' '*' '*' '0,2,4,6' 'clearlog.sh && dmesg -c'
or let them run at different minutes.

Code: Select all

RT_cmd_1 write_crontab.sh '5' '2' '*' '*' '0,2,4,6' 'clearlog.sh'
RT_cmd_2 write_crontab.sh '6' '2' '*' '*' '0,2,4,6' 'dmesg -c'
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
paaaja
Regular
Regular
Posts: 45
Joined: Fri Jun 04, 2010 5:18 pm

Re: RouterTech Firmware 2.96 Discussion

Post by paaaja » Fri May 20, 2011 8:24 pm

Wouldn't it be great if the "dmesg -c" feature was mentioned in the FAQ under

Q: How can I optimise memory on my router?

clearlog.sh is already (t)here. I personally didn't know that "dmesg -c" even existed. I used "dmesg" for a couple of times to see what was going on in my device.
User avatar
thechief
RouterTech Team
RouterTech Team
Posts: 12066
Joined: Wed Feb 01, 2006 10:22 pm
Location: England, the Centre of Africa
Contact:

Re: RouterTech Firmware 2.96 Discussion

Post by thechief » Fri May 20, 2011 8:40 pm

Yes, it could be in the FAQ as a separate item (it is called by freememory.sh).
The Chief: :afro: Be sure to read the Firmware FAQ and do a Forum Search before posting!
No support via PM. Ask all questions on the open forum.
paaaja
Regular
Regular
Posts: 45
Joined: Fri Jun 04, 2010 5:18 pm

Re: RouterTech Firmware 2.96 Discussion

Post by paaaja » Fri May 20, 2011 8:49 pm

Great. Didn't know that. Thanks.
void
Newbie
Newbie
Posts: 7
Joined: Mon Apr 25, 2011 2:26 am

Re: RouterTech Firmware 2.96 Discussion

Post by void » Sat May 21, 2011 2:20 am

See these words in the FAQ:
"Make sure that you don't have more than one active connection - if you are not using the default "quickstart" connection, then you must delete it; "

oh, should be the reason. :D Thanks for your help, thechief
champajuan
Newbie
Newbie
Posts: 3
Joined: Mon Dec 13, 2010 12:48 pm

Re: RouterTech Firmware 2.96 Discussion

Post by champajuan » Fri Jun 03, 2011 12:57 pm

void wrote:Changelog:

15. The "Restart" button in the "System" menu has been removed. There was no point in having two ways of rebooting the router in the web admin. Use "Tools->Reboot Router" instead.
It is not redundant too System and Tools Menus that are the same?
Post Reply